1719-OB2 - In Stock | Allen Bradley PLC 1719 Ex I/O

×

1719-OB2

1719-OB2

Revisions: Ser A 
Description: The Allen-Bradley 1719-OB2 module is a digital type of industrial output module. It has been designed and manufactured as part of the Allen-Bradley 1719 Ex I/O series. The 1719-OB2 digital output module has 2 output channels which are independent and it can be used for driving LEDs, sounders, or solenoids in a system. When this digital output module is used in a safety application, its output can be switched off remotely through a contact, and its intrinsically safe outputs are galvanically isolated from its power supply and bus. The 1719-OB2 digital output module can operate with either positive or negative logic, and the logic is user-selectable.
Rated 5 with 16 reviews
About | Product Specifications | FAQ

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

In Stock Ships Today

Submit RFQ for 1719-OB2

Add more parts to quote

Description: The Allen-Bradley 1719-OB2 module is a digital type of industrial output module. It has been designed and manufactured as part of the Allen-Bradley 1719 Ex I/O series. The 1719-OB2 digital output module has 2 output channels which are independent and it can be used for driving LEDs, sounders, or solenoids in a system. When this digital output module is used in a safety application, its output can be switched off remotely through a contact, and its intrinsically safe outputs are galvanically isolated from its power supply and bus. The 1719-OB2 digital output module can operate with either positive or negative logic, and the logic is user-selectable.
About | Products Specs | FAQ

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: Ser A 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the 1719-OB2.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 5 with 16 reviews

    Technical Specifications for 1719-OB2

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1719-OB2
Product LineBulletin 1719 Ex I/O module
Module TypeI/O Module
Channels2
Power Supply24 Volts
Wire typeUnshielded
Wire size0.14 to 1.5 millimeters squared
InterfaceEthernet/IP
Dimensions1.26 x 3.9 x 4 inches
Installation AreaZone 2 or Class I, Division 2
EnclosureIP20
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1719-OB2
Product LineBulletin 1719 Ex I/O module
Module TypeI/O Module
Channels2
Power Supply24 Volts
Wire typeUnshielded
Wire size0.14 to 1.5 millimeters squared
InterfaceEthernet/IP
Dimensions1.26 x 3.9 x 4 inches
Installation AreaZone 2 or Class I, Division 2
EnclosureIP20
s

About 1719-OB2

The 1719-OB2 is an Allen-Bradley device. It is an Ex I/O digital module using 2 points. It comes with 2 independent channels and runs with a 23 Volts voltage supply. It belongs to the Bulletin series of I/O modules by Allen-Bradley. This module is used to drive solenoids, LEDs, and sounders. These I/O stations modify signals and play the role of an interface to help signals communicate between control systems and field devices. An Ethernet IP adapter is used as an interface between the I/O modules and the process control systems. The 1719-OB2 has different components attached to its body. It comes with various field connection ports and ports that can be used for extensions too. There is a service interface located with the extension cable port. The module uses unshielded squared wires which are 0.14 to 0.15 millimeters in size. The installation of this module can only be done in Zone 2 or Class I, Division 2 areas and it can have vertical or horizontal mounting in Zone 2 areas.





The 1719-OB2 comes with a wide range of features. It has selectable positive or negative logic. It comes with line fault detection, with a single LED attached per channel. It is a self-monitored device and it can also be configured in its high current mode. The output of the device is bus-independent. The module can also be exchanged under voltage even when the area is non-hazardous. The 1719-OB2 supports the HART field as a communication protocol. HART is widely accepted in most industries as a standard feature for enhanced digital communication with microprocessor-enabled smart field devices. The backplane enclosure of the module has been rated as an IP20 enclosure. It is a compact-sized device and it has dimensions of 1.26 x 3.9 x 4 inches. It has been built to run in environmental conditions outlined in the ISA-S71 or security level G3 standards. It needs an environment with non-condensing humidity for proper operation.



FAQ for 1719-OB2

Does the 1719-OB2 have an Ethernet IP adapter?


Yes, the 1719-OB2 has an Ethernet IP adapter?

Does the 1719-OB2 have line fault detection?


Yes, the 1719-OB2 has line fault detection.

Does the 1719-OB2 have an IP20 enclosure?


Yes, the 1719-OB2 has an IP20 enclosure.

How many independent channels does the 1719-OB2 have?


The 1719-OB2 has 2 independent channels.

What are the 1719-OB2's dimensions?


The 1719-OB2's dimensions are 1.26 x 3.9 x 4 inches.

Does the 1719-OB2 support the HART protocol?


Yes, the 1719-OB2 supports the HART protocol.

Technical Description of 1719-OB2

The Ex I/O 2 Point Digital Output 23V module has 2 Channels and has a 24 Volt Power Supply. It has an unshielded wire type. The wire size is between 0.14 and 1.5 millimeters.

Repair Services for 1719-OB2

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1719-OB2. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions for 1719-OB2

Please refer to the manual for more information about the 1719-OB2 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1719-OB2 Ser A
1719-OB2/A, Series A, Rev A Request Quote
Common misspellings:
  • l719-OB2
  • 17l9-OB2
  • 1719-0B2
  • 1719-O82
  • 1719OB2

Dimensions For 1719-OB2

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For 1719-OB2

Resolutions For 1719-OB2

About

Technical Specifications for 1719-OB2

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1719-OB2
Product LineBulletin 1719 Ex I/O module
Module TypeI/O Module
Channels2
Power Supply24 Volts
Wire typeUnshielded
Wire size0.14 to 1.5 millimeters squared
InterfaceEthernet/IP
Dimensions1.26 x 3.9 x 4 inches
Installation AreaZone 2 or Class I, Division 2
EnclosureIP20
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1719-OB2
Product LineBulletin 1719 Ex I/O module
Module TypeI/O Module
Channels2
Power Supply24 Volts
Wire typeUnshielded
Wire size0.14 to 1.5 millimeters squared
InterfaceEthernet/IP
Dimensions1.26 x 3.9 x 4 inches
Installation AreaZone 2 or Class I, Division 2
EnclosureIP20

About 1719-OB2

The 1719-OB2 is an Allen-Bradley device. It is an Ex I/O digital module using 2 points. It comes with 2 independent channels and runs with a 23 Volts voltage supply. It belongs to the Bulletin series of I/O modules by Allen-Bradley. This module is used to drive solenoids, LEDs, and sounders. These I/O stations modify signals and play the role of an interface to help signals communicate between control systems and field devices. An Ethernet IP adapter is used as an interface between the I/O modules and the process control systems. The 1719-OB2 has different components attached to its body. It comes with various field connection ports and ports that can be used for extensions too. There is a service interface located with the extension cable port. The module uses unshielded squared wires which are 0.14 to 0.15 millimeters in size. The installation of this module can only be done in Zone 2 or Class I, Division 2 areas and it can have vertical or horizontal mounting in Zone 2 areas.





The 1719-OB2 comes with a wide range of features. It has selectable positive or negative logic. It comes with line fault detection, with a single LED attached per channel. It is a self-monitored device and it can also be configured in its high current mode. The output of the device is bus-independent. The module can also be exchanged under voltage even when the area is non-hazardous. The 1719-OB2 supports the HART field as a communication protocol. HART is widely accepted in most industries as a standard feature for enhanced digital communication with microprocessor-enabled smart field devices. The backplane enclosure of the module has been rated as an IP20 enclosure. It is a compact-sized device and it has dimensions of 1.26 x 3.9 x 4 inches. It has been built to run in environmental conditions outlined in the ISA-S71 or security level G3 standards. It needs an environment with non-condensing humidity for proper operation.



FAQ for 1719-OB2

Does the 1719-OB2 have an Ethernet IP adapter?


Yes, the 1719-OB2 has an Ethernet IP adapter?

Does the 1719-OB2 have line fault detection?


Yes, the 1719-OB2 has line fault detection.

Does the 1719-OB2 have an IP20 enclosure?


Yes, the 1719-OB2 has an IP20 enclosure.

How many independent channels does the 1719-OB2 have?


The 1719-OB2 has 2 independent channels.

What are the 1719-OB2's dimensions?


The 1719-OB2's dimensions are 1.26 x 3.9 x 4 inches.

Does the 1719-OB2 support the HART protocol?


Yes, the 1719-OB2 supports the HART protocol.

Technical Description of 1719-OB2

The Ex I/O 2 Point Digital Output 23V module has 2 Channels and has a 24 Volt Power Supply. It has an unshielded wire type. The wire size is between 0.14 and 1.5 millimeters.
Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1719-OB2. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1719-OB2. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the 1719-OB2 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1719-OB2 Ser A
1719-OB2/A, Series A, Rev A Request Quote

Common misspellings:
  • l719-OB2
  • 17l9-OB2
  • 1719-0B2
  • 1719-O82
  • 1719OB2
PDF
1719-OB2 PDF