Free UPS Ground on All Orders!
Request a
Fast Quote
Account
Cart
Quote
+1 (919) 205-4392
Allen Bradley 1336 PCB Boards 1336-BDB-SP28C

Product image is representative; revision or series may vary. Contact us to request a specific version.

1336-BDB-SP28C

|
Need a Specific Revision?

The Allen-Bradley 1336-BDB-SP28C gate drive PCB is made for the 1336 Plus, Plus II, Impact, and Force AC drives. It is compatible with the C-frame 1336 drives with 460 Volts AC voltage ratings and 60 Horsepower output power ratings.

Call for an immediate quote
2 Year DO Supply Warranty
Available
Ships from Raleigh, NC
Not an Authorized Distributor: DO Supply is not an authorized distributor for listed manufacturers or tradenames and therefore the manufacturer's warranty does not apply. All of our products come with DO Supply's 2-year warranty.
Learn more
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Technical specifications for 1336-BDB-SP28C

ManufacturerAllen Bradley
CategoryDrives
Product Line1336 PCB Boards
Part Number1336-BDB-SP28C
Weight0.75 lbs (0.34 kg)
DescriptionPCB Gate Driver Board
Voltage460 Volts AC
Power Rating60 Horsepower
FrameC
Units of Kits per Drive1
Location Within The DriveMounting plate inside the board
Documentation1336 IMPACT-6.2, 1336 FORCE-6.2, or 1336 PLUS-6.2 trouble-shooting guide
Operating Temperature0 to 50 Degrees Celsius
Product Lifecycle Status*Discontinued/Obsolete

* The Allen Bradley 1336-BDB-SP28C has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement 1336-BDB-SP28C units instead of migration.

Request a Repair

The Allen-Bradley 1336-BDB-SP28C (Series C) gate drive PCB is a printed circuit gate driver board for the 1336 Force, Impact, Plus II, and Plus AC drive families. This board provides high input gate control, and it is located beside the main control board and the chassis. The 1336-BDB-SP28C PCB is shipped as a gate drive board assembly comprising one gate drive board, and an installation kit that includes fastening screws and an installation manual. The 1336-BDB-SP28C PCB is compatible with the A and B Series boards, and it has since been replaced with the newer 1336-BDB-SP28D PCB. The 1336-BDB-SP28C PCB is suitable for the D-frame 1336 Force, Impact, Plus II, and Plus drives with 460 Volts AC voltage ratings and 60 Horsepower output ratings.

The 1336-BDB-SP28C PCB should be tested for optimal conditions whenever one or more of the modules are replaced. Testing is done by using a meter that is first set to the resistance mode and tested for open conditions on fuses 1 and 3, and then it is set to diode mode and the technicians compare the readings with standard table readings. To replace the gate drive board, it is recommended to first turn off the power and check for the absence of control voltage and for zero voltage at the +DC and –DC brake terminals. After that, open the drive enclosure and remove the control board mounting plate. Disconnect the 7 jumper connectors on the board and wires at terminal strips TB7 and TB4. Remove the screws fastening the board to the mounting plate and detach the old board. Replace the old board with a new one and reconnect the drive in the reverse order of the replacement process.