DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Warranty: | 1 year DO Supply Warranty Included |
Shipping: | Worldwide shipping via UPS, DHL, and TNT |
Repairs: | We offer repair service for the 1336-BDB-SP64D. |
Exchange: | Exchange credit for your defective unit available. |
Conditions: | We sell preowned surplus and refurbished parts. |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Part Number/Catalog No. | 1336-BDB-SP64D |
Description | PCB Gate Drive Board |
Voltage | 460V AC |
Horsepower | 3 HP |
Frame Model | A,B,C,D, or E |
Alternative Part Number | 74103-244-76 |
Product Lifecycle Status* | Discontinued/Obsolete |
*The Allen Bradley 1336-BDB-SP64D has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement 1336-BDB-SP64D units instead of migration.
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Part Number/Catalog No. | 1336-BDB-SP64D |
Description | PCB Gate Drive Board |
Voltage | 460V AC |
Horsepower | 3 HP |
Frame Model | A,B,C,D, or E |
Alternative Part Number | 74103-244-76 |
Product Lifecycle Status* | Discontinued/Obsolete |
*The Allen Bradley 1336-BDB-SP64D has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement 1336-BDB-SP64D units instead of migration.
sThe Allen-Bradley’s 1336-BDB-SP64D is a Gate Drive Board features a Horsepower of 3 and operates on 460 Volts AC. It belongs to the family of PCB Gate Drive Board Series. This Gate Drive Board Module contains brake chopper modules each of which features a thermostat which helps to provide protection to the board so that it cannot be overheated and go through component damage. The user can set parameter 11 to “disabled”, but only when the dynamic braking is installed in the 1336-BDB-SP64D Gate Drive Board. The 1336-BDB-SP64D PCB Gated Drive Board can also be programmed to “ramp-to-stop”, only during braking for deceleration. All the brake module ratings contained in this drive contain a fault contact which helps to provide a remote output signal. All the installation instructions to do with this brake chopper module are very important. The brake chopper module is to be installed in a vertical position. The brake modules should also be spaced out living a minimum clearance of 152.4 millimeters.
All the brake resistor banks that are featured in the 1336-BDB-SP64D PCB Gate Drive Board Series should be mounted externally to the enclosure by the user or an experienced technician. The surface on which this Gate Drive Board is to be mounted should also be non-combustible. At times, the brake chopper could use more than one module. If this is the case, then the additional modules should be mounted within 10 feet of the chopper module. The measurements should be exact. The user should also put dependent applications into consideration during installation.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Please refer to the manual for more information about the 1336-BDB-SP64D such as the wiring diagrams, data sheets and migration or obsolescence details.
Revision Part # | Also Known as | Availability |
1336-BDB-SP64D Ser A
|
1336-BDB-SP64D/A, Series A, Rev A | Request Quote |
Size | |
Input Type | |
Panel Cutout Height | in mm |
Panel Cutout Width | in mm |
Terminal Height | in mm |
Terminal Width | in mm |
Terminal Overall Depth | in mm |
Terminal Mounted Depth | in mm |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Part Number/Catalog No. | 1336-BDB-SP64D |
Description | PCB Gate Drive Board |
Voltage | 460V AC |
Horsepower | 3 HP |
Frame Model | A,B,C,D, or E |
Alternative Part Number | 74103-244-76 |
Product Lifecycle Status* | Discontinued/Obsolete |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Part Number/Catalog No. | 1336-BDB-SP64D |
Description | PCB Gate Drive Board |
Voltage | 460V AC |
Horsepower | 3 HP |
Frame Model | A,B,C,D, or E |
Alternative Part Number | 74103-244-76 |
Product Lifecycle Status* | Discontinued/Obsolete |
*The Allen Bradley 1336-BDB-SP64D has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement 1336-BDB-SP64D units instead of migration.
The Allen-Bradley’s 1336-BDB-SP64D is a Gate Drive Board features a Horsepower of 3 and operates on 460 Volts AC. It belongs to the family of PCB Gate Drive Board Series. This Gate Drive Board Module contains brake chopper modules each of which features a thermostat which helps to provide protection to the board so that it cannot be overheated and go through component damage. The user can set parameter 11 to “disabled”, but only when the dynamic braking is installed in the 1336-BDB-SP64D Gate Drive Board. The 1336-BDB-SP64D PCB Gated Drive Board can also be programmed to “ramp-to-stop”, only during braking for deceleration. All the brake module ratings contained in this drive contain a fault contact which helps to provide a remote output signal. All the installation instructions to do with this brake chopper module are very important. The brake chopper module is to be installed in a vertical position. The brake modules should also be spaced out living a minimum clearance of 152.4 millimeters.
All the brake resistor banks that are featured in the 1336-BDB-SP64D PCB Gate Drive Board Series should be mounted externally to the enclosure by the user or an experienced technician. The surface on which this Gate Drive Board is to be mounted should also be non-combustible. At times, the brake chopper could use more than one module. If this is the case, then the additional modules should be mounted within 10 feet of the chopper module. The measurements should be exact. The user should also put dependent applications into consideration during installation.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Please refer to the manual for more information about the 1336-BDB-SP64D such as the wiring diagrams, data sheets and migration or obsolescence details.
Revision Part # | Also Known as | Availability |
1336-BDB-SP64D Ser A
|
1336-BDB-SP64D/A, Series A, Rev A | Request Quote |