1336F-MCB-SP1J
DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Warranty: | 1 year DO Supply Warranty Included |
Shipping: | Worldwide shipping via UPS, DHL, and TNT |
Repairs: | We offer repair service for the 1336F-MCB-SP1J. |
Exchange: | Exchange credit for your defective unit available. |
Conditions: | We sell preowned surplus and refurbished parts. |
Brand | Allen-Bradley / Rockwell Automation |
Series | 1336 |
Part Number | 1336F-MCB-SP1J |
Product type | Main Control Board PCB |
Compatibility | 1336 PLUS, PLUS II, Force, Impact, and Regen Drives |
Frames | B to G |
PCBs per Drive | 1 |
Drive Voltage | 230 to 460 Volts AC |
Reference | Positive Ground Bus |
Jumper Removal | Pins 3, 4, 17, and 18 |
Brand | Allen-Bradley / Rockwell Automation |
Series | 1336 |
Part Number | 1336F-MCB-SP1J |
Product type | Main Control Board PCB |
Compatibility | 1336 PLUS, PLUS II, Force, Impact, and Regen Drives |
Frames | B to G |
PCBs per Drive | 1 |
Drive Voltage | 230 to 460 Volts AC |
Reference | Positive Ground Bus |
Jumper Removal | Pins 3, 4, 17, and 18 |
The 1336F-MCB-SP1J PCB is the main control board PCB for an Allen-Bradley 1336 PLUS, PLUS II, Force, Impact, and Regen series variable frequency drives. It is compatible with frames B to G. The 1336F-MCB-SP1J PCB is compatible with 230 Volts AC rated 1336 PLUS, PLUS II, Force, and Impact drives and 460 Volts AC and 575 Volts AC rated 1336 PLUS, PLUS II, Force, Impact, and Regen drives. One 1336F-MCB-SP1J main control board PCB is required per drive. All PCBs except the main control board are referenced to the negative ground bus in the system. When the 1336F-MCB-SP1J main control board PCB is being installed, the jumper on pins 3, 4, 17, and 18 of J2 need to be removed and the proper input mode needs to be selected.
These jumpers need to be reinstalled after the board is removed and the input mode parameter needs to be set to Status 1. Some PCBs on the drive contain hazardous voltage levels. Therefore, the drive power should be disconnected before any PCB is removed or replaced. The bus voltage on the drive should be allowed to discharge to zero after the power disconnection. The bus voltage can be measured at the test points provided for this purpose. Allen-Bradley does not recommend use of oscilloscopes for the measurement of high voltages because doing so can lead to serious injury. During drive troubleshooting, the speed reference should be set to the minimum, the proper motor-rotation direction should be selected, and the motor should be disconnected from its load.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 1336F-MCB-SP1J. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Size | |
Input Type | |
Panel Cutout Height | in mm |
Panel Cutout Width | in mm |
Terminal Height | in mm |
Terminal Width | in mm |
Terminal Overall Depth | in mm |
Terminal Mounted Depth | in mm |
Brand | Allen-Bradley / Rockwell Automation |
Series | 1336 |
Part Number | 1336F-MCB-SP1J |
Product type | Main Control Board PCB |
Compatibility | 1336 PLUS, PLUS II, Force, Impact, and Regen Drives |
Frames | B to G |
PCBs per Drive | 1 |
Drive Voltage | 230 to 460 Volts AC |
Reference | Positive Ground Bus |
Jumper Removal | Pins 3, 4, 17, and 18 |
Brand | Allen-Bradley / Rockwell Automation |
Series | 1336 |
Part Number | 1336F-MCB-SP1J |
Product type | Main Control Board PCB |
Compatibility | 1336 PLUS, PLUS II, Force, Impact, and Regen Drives |
Frames | B to G |
PCBs per Drive | 1 |
Drive Voltage | 230 to 460 Volts AC |
Reference | Positive Ground Bus |
Jumper Removal | Pins 3, 4, 17, and 18 |
The 1336F-MCB-SP1J PCB is the main control board PCB for an Allen-Bradley 1336 PLUS, PLUS II, Force, Impact, and Regen series variable frequency drives. It is compatible with frames B to G. The 1336F-MCB-SP1J PCB is compatible with 230 Volts AC rated 1336 PLUS, PLUS II, Force, and Impact drives and 460 Volts AC and 575 Volts AC rated 1336 PLUS, PLUS II, Force, Impact, and Regen drives. One 1336F-MCB-SP1J main control board PCB is required per drive. All PCBs except the main control board are referenced to the negative ground bus in the system. When the 1336F-MCB-SP1J main control board PCB is being installed, the jumper on pins 3, 4, 17, and 18 of J2 need to be removed and the proper input mode needs to be selected.
These jumpers need to be reinstalled after the board is removed and the input mode parameter needs to be set to Status 1. Some PCBs on the drive contain hazardous voltage levels. Therefore, the drive power should be disconnected before any PCB is removed or replaced. The bus voltage on the drive should be allowed to discharge to zero after the power disconnection. The bus voltage can be measured at the test points provided for this purpose. Allen-Bradley does not recommend use of oscilloscopes for the measurement of high voltages because doing so can lead to serious injury. During drive troubleshooting, the speed reference should be set to the minimum, the proper motor-rotation direction should be selected, and the motor should be disconnected from its load.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 1336F-MCB-SP1J. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 1336F-MCB-SP1J. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.