DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Warranty: | 1 year DO Supply Warranty Included |
Shipping: | Worldwide shipping via UPS, DHL, and TNT |
Repairs: | We offer repair service for the SP-119527. |
Exchange: | Exchange credit for your defective unit available. |
Conditions: | We sell preowned surplus and refurbished parts. |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Product Lifecycle Status* | Discontinued/Obsolete |
*The Allen Bradley SP-119527 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement SP-119527 units instead of migration.
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Product Lifecycle Status* | Discontinued/Obsolete |
*The Allen Bradley SP-119527 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement SP-119527 units instead of migration.
sThe Allen-Bradley SP-119527 is a node adapter board for 1395 Digital DC Drive. Alternate part numbers for this module are the 119527 and the 1395-119527. It allows the drive to be controlled using a PLC controller. It can also be configured as a Remote Input/Output interface (RIO). It is compatible with PLC 3 or PLC 5 family of controllers. It is available for all current-rated and horsepower-rated series of 1395 drives.
The SP-119527 node adapter board contains DIP switches to select baud rate, communication type, and rack address. It can support full (8-group) or half (4-group) rack structure, both containing 16 inputs and 16 output bits. Transfer of information takes place via the Microbus at the microprocessor level. For troubleshooting and diagnostics, it contains a red “Fault” LED and a green “OK” LED to indicate processor malfunction and communication status respectively. Hard faults such as Microbus RAM, watchdogs etc. are non-recoverable and the drive must either be RESET or POWER-CYCLED to clear it. Soft faults such as Microbus Handshake, Serial Link Timeout, etc. are handled by the board itself and normal operation is resumed. Warning faults such as Overload Pending, Excessive Armature Volts, etc. could result in unpredictable operation and needs to be removed.
The SP-119527 node adapter board is intended for use in a clean and dry non-corrosive industrial location with a 0° to 65°C (32° to 149°F) ambient temperature and 5% to 95%, non-condensing relative humidity. It requires periodic maintenance for proper operation.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your SP-119527. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Please refer to the manual for more information about the SP-119527 such as the wiring diagrams, data sheets and migration or obsolescence details.
Revision Part # | Also Known as | Availability |
SP-119527 Ser A
|
SP-119527/A, Series A, Rev A | Request Quote |
Size | |
Input Type | |
Panel Cutout Height | in mm |
Panel Cutout Width | in mm |
Terminal Height | in mm |
Terminal Width | in mm |
Terminal Overall Depth | in mm |
Terminal Mounted Depth | in mm |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Product Lifecycle Status* | Discontinued/Obsolete |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Product Lifecycle Status* | Discontinued/Obsolete |
*The Allen Bradley SP-119527 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement SP-119527 units instead of migration.
The Allen-Bradley SP-119527 is a node adapter board for 1395 Digital DC Drive. Alternate part numbers for this module are the 119527 and the 1395-119527. It allows the drive to be controlled using a PLC controller. It can also be configured as a Remote Input/Output interface (RIO). It is compatible with PLC 3 or PLC 5 family of controllers. It is available for all current-rated and horsepower-rated series of 1395 drives.
The SP-119527 node adapter board contains DIP switches to select baud rate, communication type, and rack address. It can support full (8-group) or half (4-group) rack structure, both containing 16 inputs and 16 output bits. Transfer of information takes place via the Microbus at the microprocessor level. For troubleshooting and diagnostics, it contains a red “Fault” LED and a green “OK” LED to indicate processor malfunction and communication status respectively. Hard faults such as Microbus RAM, watchdogs etc. are non-recoverable and the drive must either be RESET or POWER-CYCLED to clear it. Soft faults such as Microbus Handshake, Serial Link Timeout, etc. are handled by the board itself and normal operation is resumed. Warning faults such as Overload Pending, Excessive Armature Volts, etc. could result in unpredictable operation and needs to be removed.
The SP-119527 node adapter board is intended for use in a clean and dry non-corrosive industrial location with a 0° to 65°C (32° to 149°F) ambient temperature and 5% to 95%, non-condensing relative humidity. It requires periodic maintenance for proper operation.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your SP-119527. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your SP-119527. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Please refer to the manual for more information about the SP-119527 such as the wiring diagrams, data sheets and migration or obsolescence details.
Revision Part # | Also Known as | Availability |
SP-119527 Ser A
|
SP-119527/A, Series A, Rev A | Request Quote |