Free UPS Ground on All Orders!
Request a
Fast Quote
Account
Cart
Quote
+1 (919) 205-4392
Allen Bradley MPL Servo Motors MPL-A420P-SK72AA

Product image is representative; revision or series may vary. Contact us to request a specific version.

MPL-A420P-SK72AA

|
Need a Specific Revision?

The Allen-Bradley MPL-A420P-SK72AA servo motor is an MPL series servo motor. It has a rated power output of 2 kilowatts. The MPL-A420P-SK72AA servo motor weighs 9.4 pounds.

In Stock
Ships from Raleigh, NC
2 Year DO Supply Warranty
Not an Authorized Distributor: DO Supply is not an authorized distributor for listed manufacturers or tradenames and therefore the manufacturer's warranty does not apply. All of our products come with DO Supply's 2-year warranty.
Learn more
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Technical specifications for MPL-A420P-SK72AA

ManufacturerAllen Bradley
Product TypeServo Motor
Product LineMPL Servo Motors
Part NumberMPL-A420P-SK72AA
Weight12.00 lbs (5.44 kg)
Voltage Class200 Volts AC
Protection RatingIP 50
MountingFlange
Rated Speed5000 RPM
Maximum Speed5000 RPM
Output Power2 kilowatts
Frame size115 millimeters
Holding BrakeNone
Request a Repair

The MPL-A420P-SK72AA servo motor is an Allen-Bradley MPL series servo motor. It is a flange-mounted motor. A mounting pilot is provided for aligning the motor on the machine. Allen-Bradley recommends the use of stainless steel fasteners. The installation of the servo motor should comply with all the local safety regulations. The installation practices used should always promote safety and electromagnetic compatibility. Power should not be applied to an unmounted servo motor or to an unconnected cable. The cables that are used should all be restrained so that there is no uneven tension or flexing at the cable connections. The circular DIN connector on the MPL-A420P-SK72AA servo motor can be rotated by up to 180 degrees in either direction. Note that excessive connector rotation or force can damage the connector and reduce the IP rating of the motor.

The Allen-Bradley MPL-A420P-SK72AA MPL series servo motor has an IP 50 environmental protection rating. To improve this rating, an optional seal kit and sealed cable connectors need to be used. The rated speed and the maximum speed of the MPL-A420P-SK72AA servo motor are both 5000 RPM. The continuous and peak stall torque ratings are 43 pounds on an inch and 90 pounds on an inch, respectively. The MPL-A420P-SK72AA servo motor can deliver a maximum of 2 kilowatts of power at its output. The weight of the MPL-A420P-SK72AA servo motor is approximately 9.4 pounds. The input of the motor is designed for 200 Volts AC rated voltage. The frame size and magnet stack length of the motor are 115 millimeters and 2 inches, respectively. The encoder on the motor is a 1024 sin/cos absolute single-turn encoder (Hiperface protocol). The shaft comes without a shaft key or a shaft seal. A holding brake can be ordered separately as an optional accessory if it is required. The mounting flange complies with the IEC metric standards.