1753-DNSI | Allen Bradley PLC DeviceNet Controllers

1753-DNSI

1753-DNSI

Description:

The 1753-DNSI DeviceNet Safety scanner by Allen-Bradley is used for Allen-Bradley GuardPLC controllers. The unit supports up to 32 input connections and up to 32 output connections, along with standard connections of a maximum of 63 nodes. The scanner has an open type of enclosure and it has an insulation voltage of 30 Volts continuous.  

Rated 4.9 with 18 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

Available Now

Submit RFQ for 1753-DNSI

Add more parts to quote

Description:

The 1753-DNSI DeviceNet Safety scanner by Allen-Bradley is used for Allen-Bradley GuardPLC controllers. The unit supports up to 32 input connections and up to 32 output connections, along with standard connections of a maximum of 63 nodes. The scanner has an open type of enclosure and it has an insulation voltage of 30 Volts continuous.  


DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the 1753-DNSI.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 4.9 with 18 reviews

    Technical Specifications for 1753-DNSI

BrandAllen-Bradley / Rockwell Automation
SeriesDeviceNet Controllers
Part Number1753-DNSI
Supported DeviceNet Safety input/output connections32/32
Supported DeviceNet Safety standard connectionsup to 63 nodes
Supported communication rates125/250/500 kilobytes
MountingDIN rail or panel-mounted
Enclosure typeOpen
Isolation voltage30 Volts continuous
Wire type /wire categoryCopper / category 2 – on power and communication ports
HSP cableIncluded (1753-CBLDN)
Dimensions (HxWxD)90 square millimeters x 110 millimeters x 87 cubic millimeters (3.5 square inches x 4.3 inches x 3.4 cubic inches)
Operating temperature0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit)
Storage temperature-40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit)
BrandAllen-Bradley / Rockwell Automation
SeriesDeviceNet Controllers
Part Number1753-DNSI
Supported DeviceNet Safety input/output connections32/32
Supported DeviceNet Safety standard connectionsup to 63 nodes
Supported communication rates125/250/500 kilobytes
MountingDIN rail or panel-mounted
Enclosure typeOpen
Isolation voltage30 Volts continuous
Wire type /wire categoryCopper / category 2 – on power and communication ports
HSP cableIncluded (1753-CBLDN)
Dimensions (HxWxD)90 square millimeters x 110 millimeters x 87 cubic millimeters (3.5 square inches x 4.3 inches x 3.4 cubic inches)
Operating temperature0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit)
Storage temperature-40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit)
s

About 1753-DNSI

The Allen-Bradley/Rockwell Automation DeviceNet Safety scanner that is known as the 1753-DNSI DeviceNet scanner is intended for uses with the GuardPLC series controllers. This module is used for communication through the DeviceNet Safety network and it is produced according to all the relevant industrial standards. The 1753-DNSI scanner meets the requirements of safety-related standards such as the IEC 61508 (Safety Integrity Level (SIL) 3) and EN 954-1 (Category (CAT) 4) standards. The supported applications that it can be used for are applications in the de-energized safety state. This Bulletin 1753 safety scanner uses the following mechanisms when combined with the GuardPLC system: a high-speed safety protocol (HSP) signature, a controller ID (SRS), a configuration signature, a safety network number, a safety lock, and password protection.



 



The 1753-DNSI scanner has an isolation voltage of 30 Volts continuous and it is tested to withstand a voltage of 500 Volts DC for the duration of 60 seconds. The unit uses copper wires that are Category 2 wires on the ports for power and communication. The 1753-DNSI DeviceNet Safety scanner is delivered with an HSP cable labelled with product code 1753-CBLDN. The unit allows for standard DeviceNet Safety connections with up to 63 nodes along with a maximum of 32 connections for either inputs or outputs. The 1753-DNSI safety scanner has an open enclosure and it can be mounted on DIN rail on directly on the panel. The unit supports communication rates like 125, 250, and 500 kilobytes. The scanner has the following dimensions (H x W x D): 90 millimeters x 110 millimeters x 87 millimeters or 3.5 inches x 4.3 inches x 3.4 inches.



Repair Services for 1753-DNSI

Type Lead Time Price Action
Repair Service 2-4 weeks $1594cartAdd to Cart

Our highly skilled technicians can repair your 1753-DNSI. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Dimensions For 1753-DNSI

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For 1753-DNSI

Resolutions For 1753-DNSI

About

Technical Specifications for 1753-DNSI

BrandAllen-Bradley / Rockwell Automation
SeriesDeviceNet Controllers
Part Number1753-DNSI
Supported DeviceNet Safety input/output connections32/32
Supported DeviceNet Safety standard connectionsup to 63 nodes
Supported communication rates125/250/500 kilobytes
MountingDIN rail or panel-mounted
Enclosure typeOpen
Isolation voltage30 Volts continuous
Wire type /wire categoryCopper / category 2 – on power and communication ports
HSP cableIncluded (1753-CBLDN)
Dimensions (HxWxD)90 square millimeters x 110 millimeters x 87 cubic millimeters (3.5 square inches x 4.3 inches x 3.4 cubic inches)
Operating temperature0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit)
Storage temperature-40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit)
BrandAllen-Bradley / Rockwell Automation
SeriesDeviceNet Controllers
Part Number1753-DNSI
Supported DeviceNet Safety input/output connections32/32
Supported DeviceNet Safety standard connectionsup to 63 nodes
Supported communication rates125/250/500 kilobytes
MountingDIN rail or panel-mounted
Enclosure typeOpen
Isolation voltage30 Volts continuous
Wire type /wire categoryCopper / category 2 – on power and communication ports
HSP cableIncluded (1753-CBLDN)
Dimensions (HxWxD)90 square millimeters x 110 millimeters x 87 cubic millimeters (3.5 square inches x 4.3 inches x 3.4 cubic inches)
Operating temperature0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit)
Storage temperature-40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit)

About 1753-DNSI

The Allen-Bradley/Rockwell Automation DeviceNet Safety scanner that is known as the 1753-DNSI DeviceNet scanner is intended for uses with the GuardPLC series controllers. This module is used for communication through the DeviceNet Safety network and it is produced according to all the relevant industrial standards. The 1753-DNSI scanner meets the requirements of safety-related standards such as the IEC 61508 (Safety Integrity Level (SIL) 3) and EN 954-1 (Category (CAT) 4) standards. The supported applications that it can be used for are applications in the de-energized safety state. This Bulletin 1753 safety scanner uses the following mechanisms when combined with the GuardPLC system: a high-speed safety protocol (HSP) signature, a controller ID (SRS), a configuration signature, a safety network number, a safety lock, and password protection.



 



The 1753-DNSI scanner has an isolation voltage of 30 Volts continuous and it is tested to withstand a voltage of 500 Volts DC for the duration of 60 seconds. The unit uses copper wires that are Category 2 wires on the ports for power and communication. The 1753-DNSI DeviceNet Safety scanner is delivered with an HSP cable labelled with product code 1753-CBLDN. The unit allows for standard DeviceNet Safety connections with up to 63 nodes along with a maximum of 32 connections for either inputs or outputs. The 1753-DNSI safety scanner has an open enclosure and it can be mounted on DIN rail on directly on the panel. The unit supports communication rates like 125, 250, and 500 kilobytes. The scanner has the following dimensions (H x W x D): 90 millimeters x 110 millimeters x 87 millimeters or 3.5 inches x 4.3 inches x 3.4 inches.



Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks $1594cartAdd to Cart

Our highly skilled technicians can repair your 1753-DNSI. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks $1594cartAdd to Cart

Our highly skilled technicians can repair your 1753-DNSI. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

PDF