Free UPS Ground on All Orders!
Request a
Fast Quote
Account
Cart
Quote
+1 (919) 205-4392
Allen Bradley IEC 100 Contactors 100-D110H11

Product image is representative; revision or series may vary. Contact us to request a specific version.

100-D110H11

|
Need a Specific Revision?

The Allen-Bradley 100-D110H11 contactor is a 3-pole contactor. It has a current rating of 110 Amps. The conventional contactor coil is rated for 208 Volts AC.

Call for an immediate quote
2 Year DO Supply Warranty
Available
Ships from Raleigh, NC
Not an Authorized Distributor: DO Supply is not an authorized distributor for listed manufacturers or tradenames and therefore the manufacturer's warranty does not apply. All of our products come with DO Supply's 2-year warranty.
Learn more
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Technical specifications for 100-D110H11

ManufacturerAllen Bradley
Product TypeContactor
Product LineIEC 100 Contactors
Part Number100-D110H11
Weight3.00 lbs (1.36 kg)
Coil TypeConventional
Current Rating110 Amps
Control Voltage208 Volts AC
Poles3
Mounting BasePanel
Maximum Height2000 meters
Maximum Impulse Withstand12 kilovolts
Maximum Isolation Voltage1000 Volts
Working Temperature-25 to 60 degrees Celsius
Request a Repair

The 100-D110H11 contactor is an Allen-Bradley MCS IEC 100 contactor with a conventional coil. It is a 3-pole device with a 110-Amp current rating. The coil is rated for 208 Volts AC at 60 Hertz. The auxiliary contact configuration of the 100-D110H11 contactor includes 1 NC contact and 1 NO contact. The contactor must only be commissioned and maintained by qualified personnel. The operating instructions must be read and understood before any work related to contactor installation is initiated. The power should also be disconnected before any work is initiated. The main contacts and arc-chute must be examined after a short-circuit when a short-circuit occurs. The arc-chute on the 100-D110H11 contactor is mechanically locked when either the contactor is mechanically locked or when the coil is energized. The contactor should be switched off before the arc-chute is removed.

The arc-chute on the Allen-Bradley 100-D110H11 IEC 100 series contactor can be removed by exerting more force if the contacts are welded. Slight contact welds can be repaired with a screwdriver. The main contactors, magnet coil, and arc-chute on the 100-D110H11 contactor can be replaced. Allen-Bradley recommends use of only original spare parts to assure the reliability of the contactor. The width of the contactor is 120 millimeters, the height is 252 millimeters, and the depth is 156 millimeters. The 100-D series contactors like this one can only be panel mounted. They are designed for indoor use and come with an IP 00 protection rating. The maximum altitude of the installation site should not exceed 2000 meters. The operation of the 100-D110H11 contactor at the full rated voltage requires a -25 to 60 degrees Celsius ambient temperature. The rated impulse withstand voltage is 12 kilovolts. The rated isolation voltage is 1000 Volts per IEC standards.