DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Warranty: | 1 year DO Supply Warranty Included |
Shipping: | Worldwide shipping via UPS, DHL, and TNT |
Repairs: | We offer repair service for the 1771-NA. |
Exchange: | Exchange credit for your defective unit available. |
Conditions: | We sell preowned surplus and refurbished parts. |
Brand | Allen-Bradley / Rockwell Automation |
Series | PLC 5 |
Part Number | 1771-NA |
Description | Node adapter board |
Voltage | 5 Volts DC |
Temperature | 0-60 degrees Celsius |
Altitude | 1000 meters |
Baud rate | 57.5/115 KB |
Communication | RIO |
Brand | Allen-Bradley / Rockwell Automation |
Series | PLC 5 |
Part Number | 1771-NA |
Description | Node adapter board |
Voltage | 5 Volts DC |
Temperature | 0-60 degrees Celsius |
Altitude | 1000 meters |
Baud rate | 57.5/115 KB |
Communication | RIO |
The 1771-NA node adapter board from Allen-Bradley.Rockwell Automation family is a remote I/O accessory board. It can interface analog signals with the Allen-Bradley PLC 3 and PLC 5 programmable controllers that have block transfer capabilities. The board is powered with 5 Volts DC voltage. The ambient operating temperature should be between 0 and 60 degrees Celsius. It can be used at up to an altitude of 1000 meters above sea level. It uses the RIO protocol for internal communication. The node board supports different baud rates of 57.5 and 115 kilobauds. The node adapter board comes with a small surface mounting board. It contains the components which are used for communication with a PLC controller and which help in block transfers. The 1771-NA board helps the Bulletin 1395 Allen-Bradley drives to function as a remote I/O rack to the PLC controller.
The 1771-NA board is equipped with two LED indicators on it. The red Processor Fault LED lights up when there is a processor malfunction on the node board. The green LED is illuminated when there is an active communication status between the node adapter board and the PLC controller. The 1771-NA board is located in Port B of the 1395 host drive. The board should be stored in a temperature between 0 and 60 degrees Celsius. The board is a static sensitive device and it should be handled properly during the installation to avoid static damage. A 60-pin ribbon cable connector is used for connecting the board to the drive.
The 1771-NA board is a node adapter board from Allen-Bradley/Rockwell Automation. It is powered with 5 Volts DC.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 1771-NA. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Size | |
Input Type | |
Panel Cutout Height | in mm |
Panel Cutout Width | in mm |
Terminal Height | in mm |
Terminal Width | in mm |
Terminal Overall Depth | in mm |
Terminal Mounted Depth | in mm |
Brand | Allen-Bradley / Rockwell Automation |
Series | PLC 5 |
Part Number | 1771-NA |
Description | Node adapter board |
Voltage | 5 Volts DC |
Temperature | 0-60 degrees Celsius |
Altitude | 1000 meters |
Baud rate | 57.5/115 KB |
Communication | RIO |
Brand | Allen-Bradley / Rockwell Automation |
Series | PLC 5 |
Part Number | 1771-NA |
Description | Node adapter board |
Voltage | 5 Volts DC |
Temperature | 0-60 degrees Celsius |
Altitude | 1000 meters |
Baud rate | 57.5/115 KB |
Communication | RIO |
The 1771-NA node adapter board from Allen-Bradley.Rockwell Automation family is a remote I/O accessory board. It can interface analog signals with the Allen-Bradley PLC 3 and PLC 5 programmable controllers that have block transfer capabilities. The board is powered with 5 Volts DC voltage. The ambient operating temperature should be between 0 and 60 degrees Celsius. It can be used at up to an altitude of 1000 meters above sea level. It uses the RIO protocol for internal communication. The node board supports different baud rates of 57.5 and 115 kilobauds. The node adapter board comes with a small surface mounting board. It contains the components which are used for communication with a PLC controller and which help in block transfers. The 1771-NA board helps the Bulletin 1395 Allen-Bradley drives to function as a remote I/O rack to the PLC controller.
The 1771-NA board is equipped with two LED indicators on it. The red Processor Fault LED lights up when there is a processor malfunction on the node board. The green LED is illuminated when there is an active communication status between the node adapter board and the PLC controller. The 1771-NA board is located in Port B of the 1395 host drive. The board should be stored in a temperature between 0 and 60 degrees Celsius. The board is a static sensitive device and it should be handled properly during the installation to avoid static damage. A 60-pin ribbon cable connector is used for connecting the board to the drive.
The 1771-NA board is a node adapter board from Allen-Bradley/Rockwell Automation. It is powered with 5 Volts DC.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 1771-NA. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 1771-NA. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.