1771-NBV1 | Allen Bradley PLC PLC 5

1771-NBV1

Rated 3.8 with 11 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

1771-NBV1

Revisions: Ser A Ser B Ser C 
Description: The Allen-Bradley/Rockwell Automation 1771-NBV1 I/O module is a PLC 5 series and Bulletin 1771 analog combination I/O module. It supports selectable operating voltage ratings. The voltage range of the 1771-NBV1 analog combination I/O module is +/-10 Volts DC and the current range of the module is +/-20 milliamps. The rated backplane current load for this module is 1.8 Amps. The 1771-NBV1 analog combination I/O module is rack-mountable and its operating temperature range is from 32 to 140 degrees Fahrenheit.
Available Now
Request a quote for 1771-NBV1

Description: The Allen-Bradley/Rockwell Automation 1771-NBV1 I/O module is a PLC 5 series and Bulletin 1771 analog combination I/O module. It supports selectable operating voltage ratings. The voltage range of the 1771-NBV1 analog combination I/O module is +/-10 Volts DC and the current range of the module is +/-20 milliamps. The rated backplane current load for this module is 1.8 Amps. The 1771-NBV1 analog combination I/O module is rack-mountable and its operating temperature range is from 32 to 140 degrees Fahrenheit.

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: Ser A Ser B Ser C 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the 1771-NBV1.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 3.8 with 11 reviews

    Technical Specifications for 1771-NBV1

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1771-NBV1
Module TypeN-Series Analog I/O Module
Number of Inputs6 Inputs
Input TypesVoltage/Current
Input Resolution+/- 10 Volts DC (3.3 Microvolts/bit); +/- 20 Miliamperes (1.3 Microamperes/bit)
Number of Outputs2 Outputs
Output TypeVoltage
Output Resolution+/- 10 Volts DC (1.32 Milivolts/bit)
RTP ChoiceVoltage In, 1771-RTP4; Current In, 1771-RTP3
Backplane Current1.8 Amperes
Data FormatBDC or Natural Binary
Typical AC Signal Delay (Off)45 (+/- 15) ms
Typical DC Signal Delay (Off)50 ms
Wiring Arm1771-WH
MountingRack Mountable
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1771-NBV1
Module TypeN-Series Analog I/O Module
Number of Inputs6 Inputs
Input TypesVoltage/Current
Input Resolution+/- 10 Volts DC (3.3 Microvolts/bit); +/- 20 Miliamperes (1.3 Microamperes/bit)
Number of Outputs2 Outputs
Output TypeVoltage
Output Resolution+/- 10 Volts DC (1.32 Milivolts/bit)
RTP ChoiceVoltage In, 1771-RTP4; Current In, 1771-RTP3
Backplane Current1.8 Amperes
Data FormatBDC or Natural Binary
Typical AC Signal Delay (Off)45 (+/- 15) ms
Typical DC Signal Delay (Off)50 ms
Wiring Arm1771-WH
MountingRack Mountable
s

About 1771-NBV1

The Allen-Bradley 1771-NBV1 is an analog I/O module that is part of the Allen-Bradley 1771-N product range. It is designed to offer six ±10V inputs and two ±10V outputs. The total current that is drawn by the 1771-NBV1 from its I/O chassis backplane is 1.6 A. This module is compatible with the PLC-3, the PLC-5, and the PLC-5/250 controller families.



 



The input ports on the 1771-NBV1 module support a ±10.5V (±42mA with a resistor) voltage range. The resolution on the input ports is 330µV/bit (at 15 bits with a sign bit) and the input impedance is in excess of 10megaohms. The time required to detect an open circuit on the input is less than 9s and the overvoltage protection on the inputs is 140V AC RMS (continuous). Its normal mode rejection is 50 dB / 60 dB at minimum whereas the typical value for commode mode rejection is 150 dB.  The offset drift and the gain drift are ±30µV/°C and ±35ppm/°C. The 1771-NBV1’s input bandwidth that is supported by the input ports is 9 Hz., -10.4V DC is the underrange limit, and 10.4VDC is the overrange limit.



 



The output ports on the 1771-NBV1 module support ±10.4V in open circuit with the output resolution at 1.32mV/bit (13 bits with a sign bit) and the output impedance at less than 1ohm. The outputs can drive circuits with a resistance of 1kiloohm or greater (10mA maximum), 140V AC RMS (continuous) is the overvoltage protection rating on the outputs. ±400µV/°C and ±50 ppm/°C are the offset and gain drift values. The RTP-4 is recommended for use with the 1771-NBV1 and the module power should be disconnected before insertion/removal from the I/O chassis. The 1771-NBV1 gives off 8W during operation and performs optimally in environments with ambient temperatures from 32 to 140°F at 5 to 95% humidity (non-condensing).



Technical Description of 1771-NBV1

Allen Bradley PLC 5 N-Series Analog I/O Module, 6 Inputs, 2 Outputs, 1.8 Amperes Backplane Current, BDC or Natural Binary Data Format

Repair Services for 1771-NBV1

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1771-NBV1. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions for 1771-NBV1

Please refer to the manual for more information about the 1771-NBV1 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1771-NBV1 Ser A
1771-NBV1/A, Series A, Rev A Request Quote
1771-NBV1 Ser B
1771-NBV1/B, Series B, Rev B Request Quote
1771-NBV1 Ser C
1771-NBV1/C, Series C, Rev C Request Quote
Common misspellings:
  • l771-NBV1
  • 177l-NBV1
  • 1771-N8V1
  • 1771-NBVl
  • 1771NBV1

Dimensions For 1771-NBV1

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For 1771-NBV1

Resolutions For 1771-NBV1

About

Technical Specifications for 1771-NBV1

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1771-NBV1
Module TypeN-Series Analog I/O Module
Number of Inputs6 Inputs
Input TypesVoltage/Current
Input Resolution+/- 10 Volts DC (3.3 Microvolts/bit); +/- 20 Miliamperes (1.3 Microamperes/bit)
Number of Outputs2 Outputs
Output TypeVoltage
Output Resolution+/- 10 Volts DC (1.32 Milivolts/bit)
RTP ChoiceVoltage In, 1771-RTP4; Current In, 1771-RTP3
Backplane Current1.8 Amperes
Data FormatBDC or Natural Binary
Typical AC Signal Delay (Off)45 (+/- 15) ms
Typical DC Signal Delay (Off)50 ms
Wiring Arm1771-WH
MountingRack Mountable
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1771-NBV1
Module TypeN-Series Analog I/O Module
Number of Inputs6 Inputs
Input TypesVoltage/Current
Input Resolution+/- 10 Volts DC (3.3 Microvolts/bit); +/- 20 Miliamperes (1.3 Microamperes/bit)
Number of Outputs2 Outputs
Output TypeVoltage
Output Resolution+/- 10 Volts DC (1.32 Milivolts/bit)
RTP ChoiceVoltage In, 1771-RTP4; Current In, 1771-RTP3
Backplane Current1.8 Amperes
Data FormatBDC or Natural Binary
Typical AC Signal Delay (Off)45 (+/- 15) ms
Typical DC Signal Delay (Off)50 ms
Wiring Arm1771-WH
MountingRack Mountable

About 1771-NBV1

The Allen-Bradley 1771-NBV1 is an analog I/O module that is part of the Allen-Bradley 1771-N product range. It is designed to offer six ±10V inputs and two ±10V outputs. The total current that is drawn by the 1771-NBV1 from its I/O chassis backplane is 1.6 A. This module is compatible with the PLC-3, the PLC-5, and the PLC-5/250 controller families.



 



The input ports on the 1771-NBV1 module support a ±10.5V (±42mA with a resistor) voltage range. The resolution on the input ports is 330µV/bit (at 15 bits with a sign bit) and the input impedance is in excess of 10megaohms. The time required to detect an open circuit on the input is less than 9s and the overvoltage protection on the inputs is 140V AC RMS (continuous). Its normal mode rejection is 50 dB / 60 dB at minimum whereas the typical value for commode mode rejection is 150 dB.  The offset drift and the gain drift are ±30µV/°C and ±35ppm/°C. The 1771-NBV1’s input bandwidth that is supported by the input ports is 9 Hz., -10.4V DC is the underrange limit, and 10.4VDC is the overrange limit.



 



The output ports on the 1771-NBV1 module support ±10.4V in open circuit with the output resolution at 1.32mV/bit (13 bits with a sign bit) and the output impedance at less than 1ohm. The outputs can drive circuits with a resistance of 1kiloohm or greater (10mA maximum), 140V AC RMS (continuous) is the overvoltage protection rating on the outputs. ±400µV/°C and ±50 ppm/°C are the offset and gain drift values. The RTP-4 is recommended for use with the 1771-NBV1 and the module power should be disconnected before insertion/removal from the I/O chassis. The 1771-NBV1 gives off 8W during operation and performs optimally in environments with ambient temperatures from 32 to 140°F at 5 to 95% humidity (non-condensing).



Technical Description of 1771-NBV1

Allen Bradley PLC 5 N-Series Analog I/O Module, 6 Inputs, 2 Outputs, 1.8 Amperes Backplane Current, BDC or Natural Binary Data Format
Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1771-NBV1. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1771-NBV1. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the 1771-NBV1 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1771-NBV1 Ser A
1771-NBV1/A, Series A, Rev A Request Quote
1771-NBV1 Ser B
1771-NBV1/B, Series B, Rev B Request Quote
1771-NBV1 Ser C
1771-NBV1/C, Series C, Rev C Request Quote

Common misspellings:
  • l771-NBV1
  • 177l-NBV1
  • 1771-N8V1
  • 1771-NBVl
  • 1771NBV1
PDF