1771-OQ | Allen Bradley PLC PLC 5

1771-OQ

Rated 4.7 with 4 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

1771-OQ

Revisions: Ser A Ser B 
Description: Allen Bradley PLC 5 Digital DC Output Module, 8 Outputs, 20.4-26.4 Volts DC Operating Voltage, 225 Miliamperes Backplane Current
Available Now
Request a quote for 1771-OQ

Description: Allen Bradley PLC 5 Digital DC Output Module, 8 Outputs, 20.4-26.4 Volts DC Operating Voltage, 225 Miliamperes Backplane Current

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: Ser A Ser B 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the 1771-OQ.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 4.7 with 4 reviews

    Technical Specifications for 1771-OQ

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1771-OQ
Module TypeDigital DC Output Module
Number of Outputs8 Outputs
Voltage Category10-60 Volts DC, Source
DC Operating Voltage20.4-26.4 Volts
Backplane Current225 Miliamperes
Max Continuous Current Per Output2.25 Amperes
Max Continuous Current Per Module9 Amperes
Wiring Arm1771-WF
Model StatusEarlier Model
CoatingConformal Coat
Typical AC Signal Delay (Off)45 (+/- 15) ms
Typical DC Signal Delay (Off)50 ms
Wiring Arm1771-WH
MountingRack Mountable
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1771-OQ
Module TypeDigital DC Output Module
Number of Outputs8 Outputs
Voltage Category10-60 Volts DC, Source
DC Operating Voltage20.4-26.4 Volts
Backplane Current225 Miliamperes
Max Continuous Current Per Output2.25 Amperes
Max Continuous Current Per Module9 Amperes
Wiring Arm1771-WF
Model StatusEarlier Model
CoatingConformal Coat
Typical AC Signal Delay (Off)45 (+/- 15) ms
Typical DC Signal Delay (Off)50 ms
Wiring Arm1771-WH
MountingRack Mountable
s

About 1771-OQ

The Allen-Bradley 1771-OQ is an Isolated 24V DC Output Module that is directly controlled by the PLC data table’s state of corresponding bits. It is part of the 1771 Digital DC Output Modules for PLC-5 Systems. The module has a total of eight outputs with an operating voltage range of 20.4-26.4V DC. The 1771-OQ comes with 9A of continuous current. It is ideal for applications involving DC signal termination and isolated circuits, and it can also be used in motor control centers where individual control transformers are required.

The 1771-OQ Isolated 24V DC Output requires a 225mA backplane current load. It is powered via the power supply of the 1771 I/O chassis backplane. It can be installed into any slot in the chassis except the leftmost slot that is already reserved for adapters or processors. Accuracy in keying or key placement is crucial. The keying bands in the backplane connectors should correspond with the module slots. Make sure to remove or insert keys with your fingers only. Using tools can result in backplane connector damage and possible system faults. 

Each output of the 1771-OQ contains a jumper. The module is normally used as shipped. However, if you are using solenoids, these jumpers should be removed. This will decrease the turnoff time of the solenoid and off-state clamping voltage, allowing the output to energize faster. 



Repair Services for 1771-OQ

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1771-OQ. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions for 1771-OQ

Please refer to the manual for more information about the 1771-OQ such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1771-OQ Ser A
1771-OQ/A, Series A, Rev A Request Quote
1771-OQ Ser B
1771-OQ/B, Series B, Rev B Request Quote
Common misspellings:
  • l771-OQ
  • 177l-OQ
  • 1771-0Q
  • 1771OQ

Dimensions For 1771-OQ

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For 1771-OQ

Resolutions For 1771-OQ

About

Technical Specifications for 1771-OQ

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1771-OQ
Module TypeDigital DC Output Module
Number of Outputs8 Outputs
Voltage Category10-60 Volts DC, Source
DC Operating Voltage20.4-26.4 Volts
Backplane Current225 Miliamperes
Max Continuous Current Per Output2.25 Amperes
Max Continuous Current Per Module9 Amperes
Wiring Arm1771-WF
Model StatusEarlier Model
CoatingConformal Coat
Typical AC Signal Delay (Off)45 (+/- 15) ms
Typical DC Signal Delay (Off)50 ms
Wiring Arm1771-WH
MountingRack Mountable
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1771-OQ
Module TypeDigital DC Output Module
Number of Outputs8 Outputs
Voltage Category10-60 Volts DC, Source
DC Operating Voltage20.4-26.4 Volts
Backplane Current225 Miliamperes
Max Continuous Current Per Output2.25 Amperes
Max Continuous Current Per Module9 Amperes
Wiring Arm1771-WF
Model StatusEarlier Model
CoatingConformal Coat
Typical AC Signal Delay (Off)45 (+/- 15) ms
Typical DC Signal Delay (Off)50 ms
Wiring Arm1771-WH
MountingRack Mountable

About 1771-OQ

The Allen-Bradley 1771-OQ is an Isolated 24V DC Output Module that is directly controlled by the PLC data table’s state of corresponding bits. It is part of the 1771 Digital DC Output Modules for PLC-5 Systems. The module has a total of eight outputs with an operating voltage range of 20.4-26.4V DC. The 1771-OQ comes with 9A of continuous current. It is ideal for applications involving DC signal termination and isolated circuits, and it can also be used in motor control centers where individual control transformers are required.

The 1771-OQ Isolated 24V DC Output requires a 225mA backplane current load. It is powered via the power supply of the 1771 I/O chassis backplane. It can be installed into any slot in the chassis except the leftmost slot that is already reserved for adapters or processors. Accuracy in keying or key placement is crucial. The keying bands in the backplane connectors should correspond with the module slots. Make sure to remove or insert keys with your fingers only. Using tools can result in backplane connector damage and possible system faults. 

Each output of the 1771-OQ contains a jumper. The module is normally used as shipped. However, if you are using solenoids, these jumpers should be removed. This will decrease the turnoff time of the solenoid and off-state clamping voltage, allowing the output to energize faster. 



Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1771-OQ. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1771-OQ. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the 1771-OQ such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1771-OQ Ser A
1771-OQ/A, Series A, Rev A Request Quote
1771-OQ Ser B
1771-OQ/B, Series B, Rev B Request Quote

Common misspellings:
  • l771-OQ
  • 177l-OQ
  • 1771-0Q
  • 1771OQ
PDF