1403-MM05A - In Stock | Allen Bradley 1403 Powermonitor II

×

1403-MM05A

Rated 4.6 with 13 reviews
About | Product Specifications

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

1403-MM05A

Description: The 1403-MM05A is a Power Monitor II Series Master Module manufactured by Allen-Bradley.  The 1403-MM05A comes with a microprocessor-based digital instrument that helps in integrating various parameters into industrial and commercial automation systems. The 1403-MM05A comes with onboard microprocessors with advanced field configuration communication interfaces. These allow the 1403-MM05A to act as either a standalone monitoring device or a control device. read more...
In Stock Ships Today
Request a quote for 1403-MM05A

Description: The 1403-MM05A is a Power Monitor II Series Master Module manufactured by Allen-Bradley.  The 1403-MM05A comes with a microprocessor-based digital instrument that helps in integrating various parameters into industrial and commercial automation systems. The 1403-MM05A comes with onboard microprocessors with advanced field configuration communication interfaces. These allow the 1403-MM05A to act as either a standalone monitoring device or a control device. read more...
About | Products Specs

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the 1403-MM05A.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 4.6 with 13 reviews

    Technical Specifications for 1403-MM05A

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1403-MM05A
Product TypeMaster Module
Current Inputs5
Power Supply120 to 240 Volts AC 50/60 Hertz or 125 or 250 Volts DC
Nominal Full Scale Voltage Input120 to 347 Volts
Input Impedance1 Meg-Ohm per minute
Nominal Full-Scale Current Input0 to 5 Amps
Status InputsInternal 24 Volts DC
Motor Load Switching1/3 Horsepower at 125 Volts AC
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1403-MM05A
Product TypeMaster Module
Current Inputs5
Power Supply120 to 240 Volts AC 50/60 Hertz or 125 or 250 Volts DC
Nominal Full Scale Voltage Input120 to 347 Volts
Input Impedance1 Meg-Ohm per minute
Nominal Full-Scale Current Input0 to 5 Amps
Status InputsInternal 24 Volts DC
Motor Load Switching1/3 Horsepower at 125 Volts AC
s

About 1403-MM05A

The 1403-MM05A is a Power Monitor II Series Master Module manufactured by Allen-Bradley.  The 1403-MM05A comes with a microprocessor-based digital instrument that helps in integrating various parameters into industrial and commercial automation systems. The 1403-MM05A comes with onboard microprocessors with advanced field configuration communication interfaces. These allow the 1403-MM05A to act as either a standalone monitoring device or a control device. Therefore, the 1403-MM05A can be used in any large energy monitoring network. The 1403-MM05A supports a nominal measured current of 5 Amps and a measured voltage of 120 Volts to 347 Volts L-N (208 Volts to 600 Volts L-L). The 1403-MM05A’s power supply rating is 120 to 240 Volts AC at 50 to 60 Hertz or 125 to 250 Volts DC. The 1403-MM05A has a smart communications card that provides it with two active ports for communication. The ports take the Allen-Bradley PLC RI/O network while the other port takes Allen-Bradley DF-1 Protocol. In addition, the 1403-MM05A has Ethernet communication cards. These provide it with two communication ports that use 10BaseT and 10Base5 Ethernet ports and an RS-232 Configuration Port. The single and dual-port high-speed communication modules cover a variety of networks. The Ethernet Communication Card makes the 1403-MM05A a TCP/IP compatible master module.



The 1403-MM05A meets the IEEE 519 power quality pass standards and it can be used globally. In addition, the 1403-MM05A Master Module accepts up to three display modules. When it comes to the voltage inputs, the 1403-MM05A supports nominal full-scale input of 120 Volts to 347 Volts and the input impedance is 1M ohm minimum. The 1403-MM05A control relay ratings are a maximum resistive load switching of 10 Amps at 250 Volts. This translates to 2500 Volts AC. On the other side, the minimum Load Switching is 10 Amps at 24 Volts. For the DC rating, the maximum resistive load switching is 10 Amps at 30 Volts and 0.25 Amps at 250 Volts. In DC voltage, the minimum load switching is 10 Amps at 24 Volts.

Technical Description of 1403-MM05A

The Allen-Bradley 1403-MM05A Master Module has 5 Current Inputs, a 120V/240V AC 50/60 Hz or 125V/250V DC Power Supply, and a 120V-347V Nominal Full Scale Voltage Input.

Repair Services for 1403-MM05A

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1403-MM05A. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions for 1403-MM05A

Please refer to the manual for more information about the 1403-MM05A such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1403-MM05A Ser A
1403-MM05A/A, Series A, Rev A Request Quote
1403-MM05A Ser B
1403-MM05A/B, Series B, Rev B Request Quote
1403-MM05AX
1403-MM05A/X, Series X, Rev X Request Quote
Common misspellings:
  • l403-MM05A
  • 1A03-MM05A
  • 14o3-MM05A
  • 1403-MMo5A
  • 1403MM05A

Dimensions For 1403-MM05A

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For 1403-MM05A

Resolutions For 1403-MM05A

About

Technical Specifications for 1403-MM05A

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1403-MM05A
Product TypeMaster Module
Current Inputs5
Power Supply120 to 240 Volts AC 50/60 Hertz or 125 or 250 Volts DC
Nominal Full Scale Voltage Input120 to 347 Volts
Input Impedance1 Meg-Ohm per minute
Nominal Full-Scale Current Input0 to 5 Amps
Status InputsInternal 24 Volts DC
Motor Load Switching1/3 Horsepower at 125 Volts AC
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1403-MM05A
Product TypeMaster Module
Current Inputs5
Power Supply120 to 240 Volts AC 50/60 Hertz or 125 or 250 Volts DC
Nominal Full Scale Voltage Input120 to 347 Volts
Input Impedance1 Meg-Ohm per minute
Nominal Full-Scale Current Input0 to 5 Amps
Status InputsInternal 24 Volts DC
Motor Load Switching1/3 Horsepower at 125 Volts AC

About 1403-MM05A

The 1403-MM05A is a Power Monitor II Series Master Module manufactured by Allen-Bradley.  The 1403-MM05A comes with a microprocessor-based digital instrument that helps in integrating various parameters into industrial and commercial automation systems. The 1403-MM05A comes with onboard microprocessors with advanced field configuration communication interfaces. These allow the 1403-MM05A to act as either a standalone monitoring device or a control device. Therefore, the 1403-MM05A can be used in any large energy monitoring network. The 1403-MM05A supports a nominal measured current of 5 Amps and a measured voltage of 120 Volts to 347 Volts L-N (208 Volts to 600 Volts L-L). The 1403-MM05A’s power supply rating is 120 to 240 Volts AC at 50 to 60 Hertz or 125 to 250 Volts DC. The 1403-MM05A has a smart communications card that provides it with two active ports for communication. The ports take the Allen-Bradley PLC RI/O network while the other port takes Allen-Bradley DF-1 Protocol. In addition, the 1403-MM05A has Ethernet communication cards. These provide it with two communication ports that use 10BaseT and 10Base5 Ethernet ports and an RS-232 Configuration Port. The single and dual-port high-speed communication modules cover a variety of networks. The Ethernet Communication Card makes the 1403-MM05A a TCP/IP compatible master module.



The 1403-MM05A meets the IEEE 519 power quality pass standards and it can be used globally. In addition, the 1403-MM05A Master Module accepts up to three display modules. When it comes to the voltage inputs, the 1403-MM05A supports nominal full-scale input of 120 Volts to 347 Volts and the input impedance is 1M ohm minimum. The 1403-MM05A control relay ratings are a maximum resistive load switching of 10 Amps at 250 Volts. This translates to 2500 Volts AC. On the other side, the minimum Load Switching is 10 Amps at 24 Volts. For the DC rating, the maximum resistive load switching is 10 Amps at 30 Volts and 0.25 Amps at 250 Volts. In DC voltage, the minimum load switching is 10 Amps at 24 Volts.

Technical Description of 1403-MM05A

The Allen-Bradley 1403-MM05A Master Module has 5 Current Inputs, a 120V/240V AC 50/60 Hz or 125V/250V DC Power Supply, and a 120V-347V Nominal Full Scale Voltage Input.
Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1403-MM05A. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1403-MM05A. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the 1403-MM05A such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1403-MM05A Ser A
1403-MM05A/A, Series A, Rev A Request Quote
1403-MM05A Ser B
1403-MM05A/B, Series B, Rev B Request Quote
1403-MM05AX
1403-MM05A/X, Series X, Rev X Request Quote

Common misspellings:
  • l403-MM05A
  • 1A03-MM05A
  • 14o3-MM05A
  • 1403-MMo5A
  • 1403MM05A
PDF
1403-MM05A PDF