IC693CBL303 | GE Fanuc - GE IP - Emerson Series 90-30

IC693CBL303

Rated 4.9 with 11 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

IC693CBL303

Revisions: A B 
Description: The GE Fanuc IC693CBL303 hand-held programmer cable can connect a hand-held programmer cable with the PLC and other equipment related to an application process.
Call
Request a quote for IC693CBL303

Description:

The GE Fanuc IC693CBL303 hand-held programmer cable can connect a hand-held programmer cable with the PLC and other equipment related to an application process.


DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: A B 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the IC693CBL303.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 4.9 with 11 reviews

    Technical Specifications for IC693CBL303

BrandGE Fanuc
SeriesSeries 90-30
Part NumberIC693CBL303
TypeCable
PurposeHHP connection
Connector typeCanon DA15S with solder pot
Connector 1st end15-pin male, D-Subminiature on both ends
Connector 2nd end15-pin male, D-Subminiature on both ends
HoodAMP 207470-1 connector shell
Hardware kitAMP 207871-1 Kit includes 2 metric screws and 2 screw clips
Cable TypeBelden 9508
AWG#24 (.22 mm2)
Cable Length6 feet (2 meters)
Product Lifecycle Status*Discontinued/Obsolete

*The GE Fanuc IC693CBL303 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement IC693CBL303 units instead of migration.

BrandGE Fanuc
SeriesSeries 90-30
Part NumberIC693CBL303
TypeCable
PurposeHHP connection
Connector typeCanon DA15S with solder pot
Connector 1st end15-pin male, D-Subminiature on both ends
Connector 2nd end15-pin male, D-Subminiature on both ends
HoodAMP 207470-1 connector shell
Hardware kitAMP 207871-1 Kit includes 2 metric screws and 2 screw clips
Cable TypeBelden 9508
AWG#24 (.22 mm2)
Cable Length6 feet (2 meters)
Product Lifecycle Status*Discontinued/Obsolete

*The GE Fanuc IC693CBL303 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement IC693CBL303 units instead of migration.

s

About IC693CBL303

The IC693CBL303 cable is a hand-held programmer cable that has been included in Series 90-30 of the PLCs manufactured by GE Fanuc. This specific cable has been created to connect the Hand-Held Programmer (HHP) known as the GE IC693PRG300 hand-held programmer to serial connectors on a PLC power supply. This cable enables the HHP and the Programmable Logic Controller or PLC to communicate with each other and with different equipment related to the application process. This cable also provides power connections to the HHP and a signal connection that indicates to the PLC that the HHP is properly connected to its serial port. The GE Fanuc IC693CBL303 hand-held programmer cable can also be used to connect the PLC RS-485 serial port to an RS-422/485 to RS-232 converter.



 



The GE Fanuc IC693CBL303 hand-held programmer cable comes with a Canon DA15S connector that consists of a 15-pin male, D-subminiature connector type with a connector shell. This cable has a length of 2 meters and the cable type is a Belden 9508 cable with a diameter of .22 millimeters square. If a different cable length is required, it can be built by combining different elements, although if the length is excessive, it could cause electrical noise and affect the signals. The GE Fanuc IC693CBL303 hand-held programmer cable's 15-pin connector has to be attached to the serial port connector on the PLC power supply. Then, the D connector on the other end of the cable has to be coupled to the HHP. To ensure proper operations, the length must be calculated properly between the length and the diameter of the cable to avoid electrical interference.



Repair Services for IC693CBL303

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC693CBL303. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions for IC693CBL303

Please refer to the manual for more information about the IC693CBL303 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
IC693CBL303A
IC693CBL303-A, Series A, Rev A Request Quote
IC693CBL303B
IC693CBL303-B, Series B, Rev B Request Quote
Common misspellings:
  • 1C693CBL303
  • IC693C8L303
  • IC693CB1303
  • IC693CBL3o3
  • IC693CBL303

Dimensions For IC693CBL303

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For IC693CBL303

Resolutions For IC693CBL303

About

Technical Specifications for IC693CBL303

BrandGE Fanuc
SeriesSeries 90-30
Part NumberIC693CBL303
TypeCable
PurposeHHP connection
Connector typeCanon DA15S with solder pot
Connector 1st end15-pin male, D-Subminiature on both ends
Connector 2nd end15-pin male, D-Subminiature on both ends
HoodAMP 207470-1 connector shell
Hardware kitAMP 207871-1 Kit includes 2 metric screws and 2 screw clips
Cable TypeBelden 9508
AWG#24 (.22 mm2)
Cable Length6 feet (2 meters)
Product Lifecycle Status*Discontinued/Obsolete
BrandGE Fanuc
SeriesSeries 90-30
Part NumberIC693CBL303
TypeCable
PurposeHHP connection
Connector typeCanon DA15S with solder pot
Connector 1st end15-pin male, D-Subminiature on both ends
Connector 2nd end15-pin male, D-Subminiature on both ends
HoodAMP 207470-1 connector shell
Hardware kitAMP 207871-1 Kit includes 2 metric screws and 2 screw clips
Cable TypeBelden 9508
AWG#24 (.22 mm2)
Cable Length6 feet (2 meters)
Product Lifecycle Status*Discontinued/Obsolete

*The GE Fanuc IC693CBL303 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement IC693CBL303 units instead of migration.

About IC693CBL303

The IC693CBL303 cable is a hand-held programmer cable that has been included in Series 90-30 of the PLCs manufactured by GE Fanuc. This specific cable has been created to connect the Hand-Held Programmer (HHP) known as the GE IC693PRG300 hand-held programmer to serial connectors on a PLC power supply. This cable enables the HHP and the Programmable Logic Controller or PLC to communicate with each other and with different equipment related to the application process. This cable also provides power connections to the HHP and a signal connection that indicates to the PLC that the HHP is properly connected to its serial port. The GE Fanuc IC693CBL303 hand-held programmer cable can also be used to connect the PLC RS-485 serial port to an RS-422/485 to RS-232 converter.



 



The GE Fanuc IC693CBL303 hand-held programmer cable comes with a Canon DA15S connector that consists of a 15-pin male, D-subminiature connector type with a connector shell. This cable has a length of 2 meters and the cable type is a Belden 9508 cable with a diameter of .22 millimeters square. If a different cable length is required, it can be built by combining different elements, although if the length is excessive, it could cause electrical noise and affect the signals. The GE Fanuc IC693CBL303 hand-held programmer cable's 15-pin connector has to be attached to the serial port connector on the PLC power supply. Then, the D connector on the other end of the cable has to be coupled to the HHP. To ensure proper operations, the length must be calculated properly between the length and the diameter of the cable to avoid electrical interference.



Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC693CBL303. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC693CBL303. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the IC693CBL303 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
IC693CBL303A
IC693CBL303/A, Series A, Rev A Request Quote
IC693CBL303B
IC693CBL303/B, Series B, Rev B Request Quote

Common misspellings:
  • IC693C8L303
  • IC693CB1303
  • IC693CBL3o3
  • IC693CBL303
PDF