IC697PWR748 - In Stock | GE Fanuc - GE IP - Emerson Series 90-70

IC697PWR748

Rated 4.9 with 18 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

IC697PWR748

Revisions: D 
Description: The GE Fanuc Automation IC697PWR748 rack-mounted power supply module provides an easy installation process and an overall rating of 90 Watts that can power 2 different racks.
In Stock Ships Today
Request a quote for IC697PWR748

Description:

The GE Fanuc Automation IC697PWR748 rack-mounted power supply module provides an easy installation process and an overall rating of 90 Watts that can power 2 different racks.


DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: D 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the IC697PWR748.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 4.9 with 18 reviews

    Technical Specifications for IC697PWR748

BrandGE Fanuc
SeriesSeries 90-70
Part NumberIC697PWR748
Nominal Rated Voltage48 VDC
Input Voltage Range35 to 60 VDC
Input Power160 Watts maximum at a full load
Input Inrush Energy28 joules maximum at 60 VDC Input
Output Power90 Watts maximum (total for all 3 outputs)
Minimum load1.0 A on +5 VDC
Ride Through Time10 milliseconds minimum
VME SupportYes
Overcurrent protectionYes
Maximum temperature50 degrees Celsius
BrandGE Fanuc
SeriesSeries 90-70
Part NumberIC697PWR748
Nominal Rated Voltage48 VDC
Input Voltage Range35 to 60 VDC
Input Power160 Watts maximum at a full load
Input Inrush Energy28 joules maximum at 60 VDC Input
Output Power90 Watts maximum (total for all 3 outputs)
Minimum load1.0 A on +5 VDC
Ride Through Time10 milliseconds minimum
VME SupportYes
Overcurrent protectionYes
Maximum temperature50 degrees Celsius
s

About IC697PWR748

The IC697PWR748 module is a rack-mounted power supply module that is designed, manufactured, and distributed by GE Fanuc Automation. This module has been designed to operate at its full capacity only, which is 90 Watts of total power. It can be plugged directly into the rack through a 48-pin backplane connector that is on the left side of the rack. This module can be used with one rack and it also has the ability to power a second rack at the same time, but only if it is compatible with the module's specifications and it does not exceed the maximum power requirements. When using the GE Fanuc Automation IC697PWR748 rack-mounted power supply module to power a second rack, the current drawn is less than 5.2 Amps and only 5 Volts of power is required in the second rack.



 





The GE Fanuc Automation IC697PWR748 rack-mounted power supply module comes with 3 outputs and each one can operate with an output power and a specific current of 5 Volts DC and 18 Amps, 12 Volts DC and 1.5 Amps, and -12 Volts DC and 1 Amp, respectively. This module operates with a nominal line voltage of 48 Volts DC and the power supply voltage can range from 35 to 60 Volts DC. The GE Fanuc Automation IC697PWR748 rack-mounted power supply module offers an electronic overcurrent limit to each one of its outputs. If the maximum current rating is exceeded, the output voltage will drop. This is done to avoid further damages to both the rack and the power module by the excessive current. In addition to plugging in the module, the users need to secure it with mounting screws. These screw come with the module.



Repair Services for IC697PWR748

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC697PWR748. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions for IC697PWR748

Please refer to the manual for more information about the IC697PWR748 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
IC697PWR748D
IC697PWR748-D, Series D, Rev D Request Quote
Common misspellings:
  • 1C697PWR748
  • IC697PWR7A8
  • IC697PWR74b
  • IC697PWR748

Dimensions For IC697PWR748

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For IC697PWR748

Resolutions For IC697PWR748

About

Technical Specifications for IC697PWR748

BrandGE Fanuc
SeriesSeries 90-70
Part NumberIC697PWR748
Nominal Rated Voltage48 VDC
Input Voltage Range35 to 60 VDC
Input Power160 Watts maximum at a full load
Input Inrush Energy28 joules maximum at 60 VDC Input
Output Power90 Watts maximum (total for all 3 outputs)
Minimum load1.0 A on +5 VDC
Ride Through Time10 milliseconds minimum
VME SupportYes
Overcurrent protectionYes
Maximum temperature50 degrees Celsius
BrandGE Fanuc
SeriesSeries 90-70
Part NumberIC697PWR748
Nominal Rated Voltage48 VDC
Input Voltage Range35 to 60 VDC
Input Power160 Watts maximum at a full load
Input Inrush Energy28 joules maximum at 60 VDC Input
Output Power90 Watts maximum (total for all 3 outputs)
Minimum load1.0 A on +5 VDC
Ride Through Time10 milliseconds minimum
VME SupportYes
Overcurrent protectionYes
Maximum temperature50 degrees Celsius

About IC697PWR748

The IC697PWR748 module is a rack-mounted power supply module that is designed, manufactured, and distributed by GE Fanuc Automation. This module has been designed to operate at its full capacity only, which is 90 Watts of total power. It can be plugged directly into the rack through a 48-pin backplane connector that is on the left side of the rack. This module can be used with one rack and it also has the ability to power a second rack at the same time, but only if it is compatible with the module's specifications and it does not exceed the maximum power requirements. When using the GE Fanuc Automation IC697PWR748 rack-mounted power supply module to power a second rack, the current drawn is less than 5.2 Amps and only 5 Volts of power is required in the second rack.



 





The GE Fanuc Automation IC697PWR748 rack-mounted power supply module comes with 3 outputs and each one can operate with an output power and a specific current of 5 Volts DC and 18 Amps, 12 Volts DC and 1.5 Amps, and -12 Volts DC and 1 Amp, respectively. This module operates with a nominal line voltage of 48 Volts DC and the power supply voltage can range from 35 to 60 Volts DC. The GE Fanuc Automation IC697PWR748 rack-mounted power supply module offers an electronic overcurrent limit to each one of its outputs. If the maximum current rating is exceeded, the output voltage will drop. This is done to avoid further damages to both the rack and the power module by the excessive current. In addition to plugging in the module, the users need to secure it with mounting screws. These screw come with the module.



Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC697PWR748. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC697PWR748. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the IC697PWR748 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
IC697PWR748D
IC697PWR748/D, Series D, Rev D Request Quote

Common misspellings:
  • IC697PWR7A8
  • IC697PWR74b
  • IC697PWR748
PDF