1305-BA06A-HAP | Allen Bradley Drives 1305 AC Drives

1305-BA06A-HAP

Rated 4.9 with 21 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

1305-BA06A-HAP

Revisions: Ser A 
Description: The Allen-Bradley/Rockwell Automation 1305-BA06A-HAP drive is an AC-powered motor control drive from the Bulletin 1305 drive series. The drive operates at 380 to 460 Volts AC 3-phase voltage, but it cannot operate with 1-phase voltage. The 1305-BA06A-HAP drive supports a maximum output current of 6 Amps (but only at 380 Volts AC). The HMI on this drive is a programmer-only type of HMI that operates in English. The 1305-BA06A-HAP drive is protected by an enclosure with an IP 30 environmental protection rating and it is meant to be mounted vertically.
Available Now
Request a quote for 1305-BA06A-HAP

Description: The Allen-Bradley/Rockwell Automation 1305-BA06A-HAP drive is an AC-powered motor control drive from the Bulletin 1305 drive series. The drive operates at 380 to 460 Volts AC 3-phase voltage, but it cannot operate with 1-phase voltage. The 1305-BA06A-HAP drive supports a maximum output current of 6 Amps (but only at 380 Volts AC). The HMI on this drive is a programmer-only type of HMI that operates in English. The 1305-BA06A-HAP drive is protected by an enclosure with an IP 30 environmental protection rating and it is meant to be mounted vertically.

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: Ser A 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the 1305-BA06A-HAP.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 4.9 with 21 reviews

    Technical Specifications for 1305-BA06A-HAP

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1305-BA06A-HAP
Product Line1305 AC Drives
Enclosure TypeIP 30 (NEMA Type 1)
Voltage380-460V, Three Phase
Human Interface ModulesProgrammer Only
LanguageEnglish
Horsepower3 HP
Motor Rating (kW, Output Current)2.2 kW 6 A
Product Lifecycle Status*Discontinued/Obsolete

*The Allen Bradley 1305-BA06A-HAP has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement 1305-BA06A-HAP units instead of migration.

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1305-BA06A-HAP
Product Line1305 AC Drives
Enclosure TypeIP 30 (NEMA Type 1)
Voltage380-460V, Three Phase
Human Interface ModulesProgrammer Only
LanguageEnglish
Horsepower3 HP
Motor Rating (kW, Output Current)2.2 kW 6 A
Product Lifecycle Status*Discontinued/Obsolete

*The Allen Bradley 1305-BA06A-HAP has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement 1305-BA06A-HAP units instead of migration.

s

About 1305-BA06A-HAP

The Allen-Bradley 1305-BA06A-HAP has a programmer-only function type of Human Interface Module which provides programming functionality from the local panel. The 1305-BA06A-HAP is one of the Bulletin 1305 AC drives and it is compatible with Bulletin 1204 Reflected Wave Reduction devices and Bulletin 1204 terminators to protect the motors from premature failure due to reflected wave impulses. The 1305-BA06A-HAP uses a general type IP30 or NEMA 1 enclosure. The current limiting is to stabilize operation and for the drive and motor protection, it is 150% for every 60 seconds and 200% for every 2 sec. The AC dynamic braking torque, without an external resistor, is only at 50% but with an external resistor, it is at 100%. The dimensions for the 1305-BA06A-HAP are as follows: 210mm (6.69in) for the width, 195mm (7.68in) for the height, and 179mm (7.05in) for the depth and approximately weighs up to 3.6 kg (8.0lb).

The control input for the start, stop, forward, or reverse functions are configurable for 2 or 3 wire controls. The jog control input is for momentary (non-maintained) input. The SW1, SW2, and the SW3 are configurable inputs for controlling 7 preset speeds and 2 acceleration/deceleration times. The 1305-BA06A-HAP has an interlock input function to enable drive operation. The external speed of the potentiometer is 10KΩ, 1 Watt. It has a non-isolated analog input impedance of 250 ohms with a 10-bit resolution for every 4-20mA, 0-10V DC analog input impedance has 100KΩ (non-isolated) with a 10-bit resolution.

The 1305-BA06A-HAP has a nominal current rating of A06 and an input voltage of 380-460V AC (3-phase) with an adjustable output voltage and 6A output current. Its input frequency is between 50 and 60 Hz with an output between 0 and 400Hz (programmable). Its motor rating is 2.2W or 31 horsepower with a power dissipation of 73W. It has 4.6 input kVA. The efficiency of the 1305-BA06A-HAP drive is 97.5% for normal operations.



Technical Description of 1305-BA06A-HAP

1305-BA06A-HAP 1305 AC Drives with IP 30 (NEMA Type 1) enclosure, 380-460V, Three Phase rating and Programmer Only interface. English language

Repair Services for 1305-BA06A-HAP

Type Lead Time Price Action
Repair Service 2-4 weeks $1624cartAdd to Cart

Our highly skilled technicians can repair your 1305-BA06A-HAP. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions for 1305-BA06A-HAP

Please refer to the manual for more information about the 1305-BA06A-HAP such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1305-BA06A-HAP Ser A
1305-BA06A-HAP/A, Series A, Rev A Request Quote
Common misspellings:
  • l305-BA06A-HAP
  • 13o5-BA06A-HAP
  • 1305-8A06A-HAP
  • 1305-BAo6A-HAP
  • 1305BA06AHAP

Dimensions For 1305-BA06A-HAP

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For 1305-BA06A-HAP

Width 6-11/16 in. (170 mm)
Height 7-11/16 in. (195 mm)
Depth w/o Pot. 7-1/4 in. (179 mm)
Depth w/ Pot. 7-1/4 in. (184.1 mm)
Weight 8.0 lb (3.6 kg)

Resolutions For 1305-BA06A-HAP

About

Technical Specifications for 1305-BA06A-HAP

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1305-BA06A-HAP
Product Line1305 AC Drives
Enclosure TypeIP 30 (NEMA Type 1)
Voltage380-460V, Three Phase
Human Interface ModulesProgrammer Only
LanguageEnglish
Horsepower3 HP
Motor Rating (kW, Output Current)2.2 kW 6 A
Product Lifecycle Status*Discontinued/Obsolete
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.1305-BA06A-HAP
Product Line1305 AC Drives
Enclosure TypeIP 30 (NEMA Type 1)
Voltage380-460V, Three Phase
Human Interface ModulesProgrammer Only
LanguageEnglish
Horsepower3 HP
Motor Rating (kW, Output Current)2.2 kW 6 A
Product Lifecycle Status*Discontinued/Obsolete

*The Allen Bradley 1305-BA06A-HAP has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement 1305-BA06A-HAP units instead of migration.

About 1305-BA06A-HAP

The Allen-Bradley 1305-BA06A-HAP has a programmer-only function type of Human Interface Module which provides programming functionality from the local panel. The 1305-BA06A-HAP is one of the Bulletin 1305 AC drives and it is compatible with Bulletin 1204 Reflected Wave Reduction devices and Bulletin 1204 terminators to protect the motors from premature failure due to reflected wave impulses. The 1305-BA06A-HAP uses a general type IP30 or NEMA 1 enclosure. The current limiting is to stabilize operation and for the drive and motor protection, it is 150% for every 60 seconds and 200% for every 2 sec. The AC dynamic braking torque, without an external resistor, is only at 50% but with an external resistor, it is at 100%. The dimensions for the 1305-BA06A-HAP are as follows: 210mm (6.69in) for the width, 195mm (7.68in) for the height, and 179mm (7.05in) for the depth and approximately weighs up to 3.6 kg (8.0lb).

The control input for the start, stop, forward, or reverse functions are configurable for 2 or 3 wire controls. The jog control input is for momentary (non-maintained) input. The SW1, SW2, and the SW3 are configurable inputs for controlling 7 preset speeds and 2 acceleration/deceleration times. The 1305-BA06A-HAP has an interlock input function to enable drive operation. The external speed of the potentiometer is 10KΩ, 1 Watt. It has a non-isolated analog input impedance of 250 ohms with a 10-bit resolution for every 4-20mA, 0-10V DC analog input impedance has 100KΩ (non-isolated) with a 10-bit resolution.

The 1305-BA06A-HAP has a nominal current rating of A06 and an input voltage of 380-460V AC (3-phase) with an adjustable output voltage and 6A output current. Its input frequency is between 50 and 60 Hz with an output between 0 and 400Hz (programmable). Its motor rating is 2.2W or 31 horsepower with a power dissipation of 73W. It has 4.6 input kVA. The efficiency of the 1305-BA06A-HAP drive is 97.5% for normal operations.



Technical Description of 1305-BA06A-HAP

1305-BA06A-HAP 1305 AC Drives with IP 30 (NEMA Type 1) enclosure, 380-460V, Three Phase rating and Programmer Only interface. English language
Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks $1624cartAdd to Cart

Our highly skilled technicians can repair your 1305-BA06A-HAP. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks $1624cartAdd to Cart

Our highly skilled technicians can repair your 1305-BA06A-HAP. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the 1305-BA06A-HAP such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1305-BA06A-HAP Ser A
1305-BA06A-HAP/A, Series A, Rev A Request Quote

Common misspellings:
  • l305-BA06A-HAP
  • 13o5-BA06A-HAP
  • 1305-8A06A-HAP
  • 1305-BAo6A-HAP
  • 1305BA06AHAP
PDF
Dimensions

Dimensions For 1305-BA06A-HAP

Width 6-11/16 in. (170 mm)
Height 7-11/16 in. (195 mm)
Depth w/o Pot. 7-1/4 in. (179 mm)
Depth w/ Pot. 7-1/4 in. (184.1 mm)
Weight 8.0 lb (3.6 kg)