2071-AP0 | Allen Bradley Drives Kinetix 3

2071-AP0

Rated 4.5 with 8 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

2071-AP0

Revisions: Ser A 
Description: The 2071-AP0 servo drive is a single-phase type of Allen-Bradley servo drive. It has been designed and manufactured by Allen-Bradley/Rockwell Automation in the Kinetix 3 servo drive series. The 2071-AP0 servo drive does not support shunt resistors. It has a continuous output power rating of 50 Watts. The 2071-AP0 servo drive has an input voltage rating of 240 Volts AC and it uses copper wire that is rated for temperatures of at least 75 degrees Celsius for its wiring.
Available Now
Request a quote for 2071-AP0

Description: The 2071-AP0 servo drive is a single-phase type of Allen-Bradley servo drive. It has been designed and manufactured by Allen-Bradley/Rockwell Automation in the Kinetix 3 servo drive series. The 2071-AP0 servo drive does not support shunt resistors. It has a continuous output power rating of 50 Watts. The 2071-AP0 servo drive has an input voltage rating of 240 Volts AC and it uses copper wire that is rated for temperatures of at least 75 degrees Celsius for its wiring.

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: Ser A 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the 2071-AP0.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 4.5 with 8 reviews

    Technical Specifications for 2071-AP0

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.2071-AP0
Product LineKinetix 3 Servo Drive
Input Voltage240V AC
PhaseOne-Phase
Output Current.6 A
Input Current1.3 A
Shunt PowerNot Applicable
Recommended MotorTL-A120P
ModeIndexing
Wattage50 Watt
CommunicationRS-232 and RS-485
UPC884951206830
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.2071-AP0
Product LineKinetix 3 Servo Drive
Input Voltage240V AC
PhaseOne-Phase
Output Current.6 A
Input Current1.3 A
Shunt PowerNot Applicable
Recommended MotorTL-A120P
ModeIndexing
Wattage50 Watt
CommunicationRS-232 and RS-485
UPC884951206830
s

About 2071-AP0

The 2071-AP0 is a component servo drive that belongs to the Kinetix 3 series. This series has been launched by Allen-Bradley. The Allen-Bradley Kinetix component servo drive has an input voltage of 240 Volts AC and a continuous output power of 50 Watts. The Allen-Bradley 2071-AP0 Kinetix component servo drive is shipped with a general-purpose power input header, a shunt resistor, and a motor power header. A connector tool and a ground clamp are provided too. Prior to the installation of the drive, it is essential to understand how to bond the whole system. Before mounting the Allen-Bradley 2071-AP0 Kinetix component servo drive, it is recommended to leave clearances in order to allow ventilation. The servo drive must be mounted in an upright position, not on its side. The recommended wiring must be copper with at least 75 degrees Celsius as the minimum rating.



The Allen-Bradley 2071-AP0 Kinetix component servo drive must be grounded in the cabinet ground bus. It needs to be attached with a braided ground strap or solid-copper wire with a diameter of at least 0.4 millimeters and a length of 100 millimeters. Grounding the equipment will prevent it from being affected by electromagnetic interference. The Allen-Bradley 2071-AP0 Kinetix component servo drive uses internal motor short-circuit protection. The recommended fuse for this feature is an FNQ-R-7 fuse. This drive also provides motor overload protection that predicts the current temperature based on the operating conditions. These protective features make of this servo motor a great option when it is installed appropriately. The height of the drive is 155 millimeters and its width is 53.0 millimeters.



Technical Description of 2071-AP0

Allen-Bradley Kinetix 3 Servo Drive with One-Phase, .6 A Output Current, and 50 Watt Power

Repair Services for 2071-AP0

Type Lead Time Price Action
Repair Service 2-4 weeks $480cartAdd to Cart
Our highly skilled technicians can repair your 2071-AP0. All of our repairs come with a 1 Year Warranty. Please contact us for additional information about our repair process.

Revisions for 2071-AP0

Please refer to the manual for more information about the 2071-AP0 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
2071-AP0 Ser A
2071-AP0/A, Series A, Rev A Request Quote
Common misspellings:
  • 2o71-AP0
  • 207l-AP0
  • 2071-APo
  • 2071AP0

Dimensions For 2071-AP0

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For 2071-AP0

Resolutions For 2071-AP0

About

Technical Specifications for 2071-AP0

ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.2071-AP0
Product LineKinetix 3 Servo Drive
Input Voltage240V AC
PhaseOne-Phase
Output Current.6 A
Input Current1.3 A
Shunt PowerNot Applicable
Recommended MotorTL-A120P
ModeIndexing
Wattage50 Watt
CommunicationRS-232 and RS-485
UPC884951206830
ManufacturerRockwell Automation
BrandAllen-Bradley
Part Number/Catalog No.2071-AP0
Product LineKinetix 3 Servo Drive
Input Voltage240V AC
PhaseOne-Phase
Output Current.6 A
Input Current1.3 A
Shunt PowerNot Applicable
Recommended MotorTL-A120P
ModeIndexing
Wattage50 Watt
CommunicationRS-232 and RS-485
UPC884951206830

About 2071-AP0

The 2071-AP0 is a component servo drive that belongs to the Kinetix 3 series. This series has been launched by Allen-Bradley. The Allen-Bradley Kinetix component servo drive has an input voltage of 240 Volts AC and a continuous output power of 50 Watts. The Allen-Bradley 2071-AP0 Kinetix component servo drive is shipped with a general-purpose power input header, a shunt resistor, and a motor power header. A connector tool and a ground clamp are provided too. Prior to the installation of the drive, it is essential to understand how to bond the whole system. Before mounting the Allen-Bradley 2071-AP0 Kinetix component servo drive, it is recommended to leave clearances in order to allow ventilation. The servo drive must be mounted in an upright position, not on its side. The recommended wiring must be copper with at least 75 degrees Celsius as the minimum rating.



The Allen-Bradley 2071-AP0 Kinetix component servo drive must be grounded in the cabinet ground bus. It needs to be attached with a braided ground strap or solid-copper wire with a diameter of at least 0.4 millimeters and a length of 100 millimeters. Grounding the equipment will prevent it from being affected by electromagnetic interference. The Allen-Bradley 2071-AP0 Kinetix component servo drive uses internal motor short-circuit protection. The recommended fuse for this feature is an FNQ-R-7 fuse. This drive also provides motor overload protection that predicts the current temperature based on the operating conditions. These protective features make of this servo motor a great option when it is installed appropriately. The height of the drive is 155 millimeters and its width is 53.0 millimeters.



Technical Description of 2071-AP0

Allen-Bradley Kinetix 3 Servo Drive with One-Phase, .6 A Output Current, and 50 Watt Power
Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks $480cartAdd to Cart
Our highly skilled technicians can repair your 2071-AP0. All of our repairs come with a 1 Year Warranty. Please contact us for additional information about our repair process.
Type Lead Time Price Action
Repair Service 2-4 weeks $480cartAdd to Cart
Our highly skilled technicians can repair your 2071-AP0. All of our repairs come with a 1 Year Warranty. Please contact us for additional information about our repair process.
Revisions

Please refer to the manual for more information about the 2071-AP0 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
2071-AP0 Ser A
2071-AP0/A, Series A, Rev A Request Quote

Common misspellings:
  • 2o71-AP0
  • 207l-AP0
  • 2071-APo
  • 2071AP0
PDF