DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty
Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Warranty: | 1 year DO Supply Warranty Included |
Shipping: | Worldwide shipping via UPS, DHL, and TNT |
Repairs: | We offer repair service for the 2080-TC2. |
Exchange: | Exchange credit for your defective unit available. |
Conditions: | We sell preowned surplus and refurbished parts. |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Part Number/Catalog No. | 2080-TC2 |
Product Type | Non-isolated Thermocouple and RTD Plug-in Module |
Mounting Torque | 0.2 Nm |
Terminal Screw Torque | 0.22-0.25 Nm |
Resolution | 14-bit |
Accuracy | +/- 1.0 *C for TC and RTD @ 25*C |
Channels | 2, Non-isolated |
Open Circuit Detection Time | 8-1515 ms |
Power Consumption | 3.3V, 40mA |
Input Impedance | > 300 K? |
CJC Error | +/-1.2 *C @ 25 *C |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Part Number/Catalog No. | 2080-TC2 |
Product Type | Non-isolated Thermocouple and RTD Plug-in Module |
Mounting Torque | 0.2 Nm |
Terminal Screw Torque | 0.22-0.25 Nm |
Resolution | 14-bit |
Accuracy | +/- 1.0 *C for TC and RTD @ 25*C |
Channels | 2, Non-isolated |
Open Circuit Detection Time | 8-1515 ms |
Power Consumption | 3.3V, 40mA |
Input Impedance | > 300 K? |
CJC Error | +/-1.2 *C @ 25 *C |
The 2080-TC2 by Allen-Bradley is a 2-channel, non-isolated thermocouple plug-in model that belongs to the Micro800 Specialty Plug-in Modules. It enhances the range of capabilities of a base unit controller by making temperature control possible when a Proportional Integral Derivative is used. Micro830 and Micro850 support this specialty module. It can be installed on any of the controller plug-in slots. The module unit ships with two module fastening screws, a pin-out guide wiring instructions, and one EPCOS B57869S0502F140 part, which is a passive negative temperature, non-polarized co-efficient CJC thermistor that is fixed to the plug-in. Be careful not to unscrew or remove this CJC thermistor.
The 2080-TC2 Thermocouple Plug-in Module has 12-pin female terminal blocks and supports sensors with ANSI and IEC code B, E, J, K, N, R, S, and T. It has a 14-bit resolution, a power consumption of 3.3 Volts, 40 mA, and an input impedance of 300 KΩ. It comes with a common mode rejection ratio of 100 dB at 50 to 60 Hertz, and normal mode rejection ratio of 70 dB at 50 to 60 Hertz. Using a 2.5 millimeter or 0.10-inch flat-blade screwdriver, apply terminal screw torque between 0.22 and 0.25 N-m (1.95 to 2.21 pounds on an inch). The plug-in can be wired before insertion into the controller or once it has been secured in place.
Cabling used with the 2080-TC2 Module must be shielded, twisted cores. At the controller end, the shield wire should be shorted to a chassis ground. The recommended wire size is between 0.14 and 1.0 millimeters squared (26 to 17 AWG) stranded copper wire or 0.14 to 1.5 millimeters squared (26 to 16 AWG) solid copper wire, both of which should be rated at a maximum insulation of 90 degrees Celsius (194 degrees Fahrenheit). Performance of the non-isolated module and entire setup will depend on the application, however, better noise immunity can be achieved by keeping cable length within the ideal length of ten meters. If working with configurations requiring longer cable length, use the 2085 expansion I/O modules.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 2080-TC2. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Please refer to the manual for more information about the 2080-TC2 such as the wiring diagrams, data sheets and migration or obsolescence details.
Revision Part # | Also Known as | Availability |
2080-TC2 Ser A
|
2080-TC2/A, Series A, Rev A | Request Quote |
Size | |
Input Type | |
Panel Cutout Height | in mm |
Panel Cutout Width | in mm |
Terminal Height | in mm |
Terminal Width | in mm |
Terminal Overall Depth | in mm |
Terminal Mounted Depth | in mm |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Part Number/Catalog No. | 2080-TC2 |
Product Type | Non-isolated Thermocouple and RTD Plug-in Module |
Mounting Torque | 0.2 Nm |
Terminal Screw Torque | 0.22-0.25 Nm |
Resolution | 14-bit |
Accuracy | +/- 1.0 *C for TC and RTD @ 25*C |
Channels | 2, Non-isolated |
Open Circuit Detection Time | 8-1515 ms |
Power Consumption | 3.3V, 40mA |
Input Impedance | > 300 K? |
CJC Error | +/-1.2 *C @ 25 *C |
Manufacturer | Rockwell Automation |
Brand | Allen-Bradley |
Part Number/Catalog No. | 2080-TC2 |
Product Type | Non-isolated Thermocouple and RTD Plug-in Module |
Mounting Torque | 0.2 Nm |
Terminal Screw Torque | 0.22-0.25 Nm |
Resolution | 14-bit |
Accuracy | +/- 1.0 *C for TC and RTD @ 25*C |
Channels | 2, Non-isolated |
Open Circuit Detection Time | 8-1515 ms |
Power Consumption | 3.3V, 40mA |
Input Impedance | > 300 K? |
CJC Error | +/-1.2 *C @ 25 *C |
The 2080-TC2 by Allen-Bradley is a 2-channel, non-isolated thermocouple plug-in model that belongs to the Micro800 Specialty Plug-in Modules. It enhances the range of capabilities of a base unit controller by making temperature control possible when a Proportional Integral Derivative is used. Micro830 and Micro850 support this specialty module. It can be installed on any of the controller plug-in slots. The module unit ships with two module fastening screws, a pin-out guide wiring instructions, and one EPCOS B57869S0502F140 part, which is a passive negative temperature, non-polarized co-efficient CJC thermistor that is fixed to the plug-in. Be careful not to unscrew or remove this CJC thermistor.
The 2080-TC2 Thermocouple Plug-in Module has 12-pin female terminal blocks and supports sensors with ANSI and IEC code B, E, J, K, N, R, S, and T. It has a 14-bit resolution, a power consumption of 3.3 Volts, 40 mA, and an input impedance of 300 KΩ. It comes with a common mode rejection ratio of 100 dB at 50 to 60 Hertz, and normal mode rejection ratio of 70 dB at 50 to 60 Hertz. Using a 2.5 millimeter or 0.10-inch flat-blade screwdriver, apply terminal screw torque between 0.22 and 0.25 N-m (1.95 to 2.21 pounds on an inch). The plug-in can be wired before insertion into the controller or once it has been secured in place.
Cabling used with the 2080-TC2 Module must be shielded, twisted cores. At the controller end, the shield wire should be shorted to a chassis ground. The recommended wire size is between 0.14 and 1.0 millimeters squared (26 to 17 AWG) stranded copper wire or 0.14 to 1.5 millimeters squared (26 to 16 AWG) solid copper wire, both of which should be rated at a maximum insulation of 90 degrees Celsius (194 degrees Fahrenheit). Performance of the non-isolated module and entire setup will depend on the application, however, better noise immunity can be achieved by keeping cable length within the ideal length of ten meters. If working with configurations requiring longer cable length, use the 2085 expansion I/O modules.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 2080-TC2. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Type | Lead Time | Price | Action |
---|---|---|---|
Repair Service | 2-4 weeks | Ask | ![]() |
Our highly skilled technicians can repair your 2080-TC2. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.
Please refer to the manual for more information about the 2080-TC2 such as the wiring diagrams, data sheets and migration or obsolescence details.
Revision Part # | Also Known as | Availability |
2080-TC2 Ser A
|
2080-TC2/A, Series A, Rev A | Request Quote |