1745-E102 | Allen Bradley PLC SLC 100

1745-E102

Rated 4.3 with 11 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

1745-E102

Revisions: Ser A 
Description: 1745-E102 by Allen Bradley is part of the SLC-100 series of PLCs. This part features 10 input terminals and 6 output terminals, and an input power range of 170-265 VAC
Available Now
Request a quote for 1745-E102

Description: 1745-E102 by Allen Bradley is part of the SLC-100 series of PLCs. This part features 10 input terminals and 6 output terminals, and an input power range of 170-265 VAC

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: Ser A 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the 1745-E102.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 4.3 with 11 reviews

    Technical Specifications for 1745-E102

ManufacturerRockwell Automation
BrandAllen-Bradley
Output Termials6
Input Terminals10
Input TypeDigital
Input Power170-265 VAC
Comm Cable1745-c2
ManufacturerRockwell Automation
BrandAllen-Bradley
Output Termials6
Input Terminals10
Input TypeDigital
Input Power170-265 VAC
Comm Cable1745-c2
s

About 1745-E102

The Allen-Bradley 1745-E102 is compatible either with an SLC 150 processor or with 100 processor units to provide more I/O circuits for a variety of applications. The 1745-E102 runs on 10-250V AC at 50-60Hz and can expand the circuitry up to a maximum of 112. Assigning addresses to the I/O combination is easy when you can match the address blocks to the 1745-E102 and other devices in the SLC 100/150 series. A 1745-C2 unit is required to interconnect the 1745-E102 expansion units with the processor unit which is a 10-pinpoint cable.



Weighing only 4 lbs, the 1745-E102 is easy to transport and install. There are various indicators for process identification, including a green indicator for DC power and red LEDs for inputs and outputs. During installation, make sure the whole unit, including the processor and expansion unit, is properly grounded to avoid damage to the device or the personnel working on it.



The 1745-E102 is connected to a processor unit using a ribbon cable. There are 3 configurations available in this series: basic, relay, and an analog input unit. The basic unit consists of 10 inputs and 6 outputs while the relay unit has no inputs and 12 output circuits powered by a voltage range of 170-265V AC. The analog circuit has 2 inputs and no output circuitry. Make sure that the 1745-E102’s wires are routed to minimize electrical noise effects.



Repair Services for 1745-E102

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1745-E102. All of our repairs come with a 1 Year Warranty. Please contact us for additional information about our repair process.

Revisions for 1745-E102

Please refer to the manual for more information about the 1745-E102 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1745-E102 Ser A
1745-E102/A, Series A, Rev A Request Quote
Common misspellings:
  • l745-E102
  • 17A5-E102
  • 1745-El02
  • 1745-E1o2
  • 1745E102

Dimensions For 1745-E102

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For 1745-E102

Resolutions For 1745-E102

About

Technical Specifications for 1745-E102

ManufacturerRockwell Automation
BrandAllen-Bradley
Output Termials6
Input Terminals10
Input TypeDigital
Input Power170-265 VAC
Comm Cable1745-c2
ManufacturerRockwell Automation
BrandAllen-Bradley
Output Termials6
Input Terminals10
Input TypeDigital
Input Power170-265 VAC
Comm Cable1745-c2

About 1745-E102

The Allen-Bradley 1745-E102 is compatible either with an SLC 150 processor or with 100 processor units to provide more I/O circuits for a variety of applications. The 1745-E102 runs on 10-250V AC at 50-60Hz and can expand the circuitry up to a maximum of 112. Assigning addresses to the I/O combination is easy when you can match the address blocks to the 1745-E102 and other devices in the SLC 100/150 series. A 1745-C2 unit is required to interconnect the 1745-E102 expansion units with the processor unit which is a 10-pinpoint cable.



Weighing only 4 lbs, the 1745-E102 is easy to transport and install. There are various indicators for process identification, including a green indicator for DC power and red LEDs for inputs and outputs. During installation, make sure the whole unit, including the processor and expansion unit, is properly grounded to avoid damage to the device or the personnel working on it.



The 1745-E102 is connected to a processor unit using a ribbon cable. There are 3 configurations available in this series: basic, relay, and an analog input unit. The basic unit consists of 10 inputs and 6 outputs while the relay unit has no inputs and 12 output circuits powered by a voltage range of 170-265V AC. The analog circuit has 2 inputs and no output circuitry. Make sure that the 1745-E102’s wires are routed to minimize electrical noise effects.



Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1745-E102. All of our repairs come with a 1 Year Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your 1745-E102. All of our repairs come with a 1 Year Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the 1745-E102 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
1745-E102 Ser A
1745-E102/A, Series A, Rev A Request Quote

Common misspellings:
  • l745-E102
  • 17A5-E102
  • 1745-El02
  • 1745-E1o2
  • 1745E102
PDF