IC693MDL754 - In Stock | GE Fanuc - GE IP - Emerson Series 90-30

IC693MDL754

Rated 5 with 12 reviews

DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.


credit cards accepted
better business bureau

IC693MDL754

Revisions: BC CC CD ED FD 
Description: The GE Fanuc IC693MDL754 module is a ESCP positive logic output module. The 32 output points on the module are divided into 2 groups of 16.
In Stock Ships Today
Request a quote for IC693MDL754

Description:

The GE Fanuc IC693MDL754 module is a ESCP positive logic output module. The 32 output points on the module are divided into 2 groups of 16.


DO Supply is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply. Product comes with DO Supply's 1-year warranty

Rockwell Disclaimer: The product is used surplus. DO Supply is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because DO Supply is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, DO Supply makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. DO Supply also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. DO Supply also makes no representations as to your right to install any such firmware on the product. DO Supply will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.

disclaimer
credit cards
better business bureau
Revisions: BC CC CD ED FD 

Warranty: 1 year DO Supply Warranty Included
Shipping: Worldwide shipping via UPS, DHL, and TNT
Repairs: We offer repair service for the IC693MDL754.
Exchange: Exchange credit for your defective unit available.
Conditions: We sell preowned surplus and refurbished parts.

To speak to a sales representative for pricing & lead time:


Rated 5 with 12 reviews

    Technical Specifications for IC693MDL754

BrandGE Fanuc
SeriesSeries 90-30
Part NumberIC693MDL754
Product typeDigital I/O
CompatibilityGE Fanuc 90-30 PLCs
Output points32
Output groups2
Output point peak current 0.75 Amps
Module current draw300 milliamps
Module voltage input5 Volts DC
Module configurationDIP switch
Product Lifecycle Status*Discontinued/Obsolete

*The GE Fanuc IC693MDL754 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement IC693MDL754 units instead of migration.

BrandGE Fanuc
SeriesSeries 90-30
Part NumberIC693MDL754
Product typeDigital I/O
CompatibilityGE Fanuc 90-30 PLCs
Output points32
Output groups2
Output point peak current 0.75 Amps
Module current draw300 milliamps
Module voltage input5 Volts DC
Module configurationDIP switch
Product Lifecycle Status*Discontinued/Obsolete

*The GE Fanuc IC693MDL754 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement IC693MDL754 units instead of migration.

s

About IC693MDL754

The IC693MDL754 output module is a 12 to 24 Volts DC and 0.75 Amps rated positive logic output module. The IC693MDL754 output module provides 32 outputs arranged in 2 isolated groups of 16 outputs, with each group having its own common. The module outputs are sourcing-type outputs which means that they supply current to the connected loads and the switch loads on the positive side. Each output can source a maximum current of 0.75 Amps. Each output point on the IC693MDL754 output module supports overcurrent and short-circuit protection. A fault is generated if an overcurrent or short-circuiting occurs and a fault signal is sent to the CPU. Additionall,y DIP switch configuration errors, loss of field-side power, and ESCP failure within any particular group will lead to the generation of a fault signal. Both output groups on the module can be used to drive separate loads.



 



The IC693MDL754 output module can be installed in a PAXSystem RX3i system or a Series 90-30 PLC. The power consumption for the module is 300 milliamps of current at 5 Volts DC bus voltage on the system backplane. At 24 Volts DC, there is no thermal derating. However, at 30 Volts DC, the outputs are derated at temperatures above 104 degrees Fahrenheit. The rated inrush current for the IC693MDL754 output module is 3 Amps without the ESCP trip. The typical steady-state overcurrent trip is 5 Amps per point. The working temperature range for the IC693MDL754 output module is 32 to 140 degrees Fahrenheit. Unused IC693MDL754 modules should be stored in a location where the ambient temperature is maintained between -40 to 185 degrees Fahrenheit. There are 2 DIP switches on the back side of the module. The DIP switch configuration must match the module’s software configuration.



Repair Services for IC693MDL754

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC693MDL754. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions for IC693MDL754

Please refer to the manual for more information about the IC693MDL754 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
IC693MDL754BC
IC693MDL754-BC, Series BC, Rev BC Request Quote
IC693MDL754CC
IC693MDL754-CC, Series CC, Rev CC Request Quote
IC693MDL754CD
IC693MDL754-CD, Series CD, Rev CD Request Quote
IC693MDL754ED
IC693MDL754-ED, Series ED, Rev ED Request Quote
IC693MDL754FD
IC693MDL754-FD, Series FD, Rev FD Request Quote
Common misspellings:
  • 1C693MDL754
  • IC693MD1754
  • IC693MDL75A
  • IC693MDL754

Dimensions For IC693MDL754

Size
Input Type
Panel Cutout Height in mm
Panel Cutout Width in mm
Terminal Height in mm
Terminal Width in mm
Terminal Overall Depth in mm
Terminal Mounted Depth in mm

Dimensions For IC693MDL754

Resolutions For IC693MDL754

About

Technical Specifications for IC693MDL754

BrandGE Fanuc
SeriesSeries 90-30
Part NumberIC693MDL754
Product typeDigital I/O
CompatibilityGE Fanuc 90-30 PLCs
Output points32
Output groups2
Output point peak current 0.75 Amps
Module current draw300 milliamps
Module voltage input5 Volts DC
Module configurationDIP switch
Product Lifecycle Status*Discontinued/Obsolete
BrandGE Fanuc
SeriesSeries 90-30
Part NumberIC693MDL754
Product typeDigital I/O
CompatibilityGE Fanuc 90-30 PLCs
Output points32
Output groups2
Output point peak current 0.75 Amps
Module current draw300 milliamps
Module voltage input5 Volts DC
Module configurationDIP switch
Product Lifecycle Status*Discontinued/Obsolete

*The GE Fanuc IC693MDL754 has been discontinued by the manufacturer, however we specialize in obsolete parts and can likely still supply surplus and/or refurbished replacement IC693MDL754 units instead of migration.

About IC693MDL754

The IC693MDL754 output module is a 12 to 24 Volts DC and 0.75 Amps rated positive logic output module. The IC693MDL754 output module provides 32 outputs arranged in 2 isolated groups of 16 outputs, with each group having its own common. The module outputs are sourcing-type outputs which means that they supply current to the connected loads and the switch loads on the positive side. Each output can source a maximum current of 0.75 Amps. Each output point on the IC693MDL754 output module supports overcurrent and short-circuit protection. A fault is generated if an overcurrent or short-circuiting occurs and a fault signal is sent to the CPU. Additionall,y DIP switch configuration errors, loss of field-side power, and ESCP failure within any particular group will lead to the generation of a fault signal. Both output groups on the module can be used to drive separate loads.



 



The IC693MDL754 output module can be installed in a PAXSystem RX3i system or a Series 90-30 PLC. The power consumption for the module is 300 milliamps of current at 5 Volts DC bus voltage on the system backplane. At 24 Volts DC, there is no thermal derating. However, at 30 Volts DC, the outputs are derated at temperatures above 104 degrees Fahrenheit. The rated inrush current for the IC693MDL754 output module is 3 Amps without the ESCP trip. The typical steady-state overcurrent trip is 5 Amps per point. The working temperature range for the IC693MDL754 output module is 32 to 140 degrees Fahrenheit. Unused IC693MDL754 modules should be stored in a location where the ambient temperature is maintained between -40 to 185 degrees Fahrenheit. There are 2 DIP switches on the back side of the module. The DIP switch configuration must match the module’s software configuration.



Repairs
Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC693MDL754. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Type Lead Time Price Action
Repair Service 2-4 weeks Askenvelope Get Quote

Our highly skilled technicians can repair your IC693MDL754. All of our repairs come with a 1 Year DO Supply Warranty. Please contact us for additional information about our repair process.

Revisions

Please refer to the manual for more information about the IC693MDL754 such as the wiring diagrams, data sheets and migration or obsolescence details.

Revision Part # Also Known as Availability
IC693MDL754-BC
IC693MDL754/BC, Series BC, Rev BC Request Quote
IC693MDL754-CC
IC693MDL754/CC, Series CC, Rev CC Request Quote
IC693MDL754-CD
IC693MDL754/CD, Series CD, Rev CD Request Quote
IC693MDL754-ED
IC693MDL754/ED, Series ED, Rev ED Request Quote
IC693MDL754-FD
IC693MDL754/FD, Series FD, Rev FD Request Quote

Common misspellings:
  • IC693MD1754
  • IC693MDL75A
  • IC693MDL754
PDF