2711-NR7T
This Allen Bradley adapter kit facilitates the installation of PanelView 1000 and 1000e series touchscreen terminals using a plate mounting type. It adheres to safety and quality standards, including
In Stock Ships Today
4.7
Free UPS Ground on All Orders!
+1 (919) 205-4392
Allen Bradley Panelview 1000
The PanelView Standard 1000 Graphic Terminals have a 10 in. grayscale or color flat-panel display with a resolution of 640 x 480. For specific PanelView terminals, PanelView is replaced with the PV abbreviation. For example: PV1000 refers to the PanelView 1000 terminal. These terminals support operator input via keypad, via touch screen or via keypad with touch screen.
Learn more
Browse Panelview 1000
Browse available units in our catalog of Panelview 1000.
2711-T10C8L1X
In Stock Ships Today
5.0
2711-NB4
This replacement kit features a lithium battery and is engineered for operation under conditions where vibration reaches up to 2g at 2000 Hz. It can withstand shocks up to 15 g, making it suitable for
Call
4.8
2711-T10C16L1X
In Stock Ships Today
5.0
2711-T10C20L1X
In Stock Ships Today
5.0
2711-NL6-SUBSTITUTE
The 2711-NL6-SUBSTITUTE backlight is specifically designed for Series B PV1000 and Series D PV1000e color terminals. It operates effectively across a temperature range of 0 to 55 degrees Celsius and h
In Stock Ships Today
4.8
2711-T10G9X
This model supports an input voltage range of 85 to 264 volts AC and operates within a frequency range of 47 to 63 Hz. The enclosure meets NEMA Type 12/13 and 4X standards (recommended for indoor use)
In Stock Ships Today
5.0
2711-K10G20X
In Stock Ships Today
5.0
2711-T10G15X
Focusing on utility, the 2711-T10G15X offers a 10.4-inch display with grayscale touchscreen capabilities. This model supports an operating temperature range from 0 to 55 °C and can be stored between -
In Stock Ships Tomorrow
5.0
2711-T10G16X
As part of the Panelview 1000 series, the 2711-T10G16X HMI terminal offers approximately 1 MB of application flash memory alongside around 310 KB of runtime RAM. It includes communication capabilities
In Stock Ships Today
5.0
Showing 111-120 of
184
results
About Panelview 1000
The PanelView 1000 Series is a family of Allen-Bradley PanelView Standard Operator Terminals that provide a range of control and monitoring capabilities that are suitable for industrial applications. The display type on each terminal is an Active Matrix Thin-Film Transistor (TFT) with a cold cathode fluorescent backlight. They are available in 640 by 480 pixels, monochrome, grayscale (4 gray colors), and color (32 colors) displays with 8.3 x 6.2-inch dimensions. The touchscreen, keypad, or touchscreen and keypad combination input options are available for the terminals in this series and they have NEMA Type 12/13, IP 54, 4X (indoor use), and IP 65 enclosures to meet the environmental requirements of different applications.
The PanelView 1000 terminals are available in 85 to 264 Volts AC or 85 to 32 Volts DC power ratings. Both the PV1000G and the PV1000C models have a flash memory of 1008 KB. The touchscreen versions weigh 3 kilograms while the keypad models weigh 3.06 kilograms. The flat and lightweight design of these terminals saves mounting space and each unit has 6 mounting clips for convenience. Applications for the PanelView 1000 terminals can be created with the PanelBuilder32 software. Their communication options include 1 RS-232 port and 1 Remote I/O communication port. The Remote I/O port on PanelView 1000 operator terminals is compatible with all Allen-Bradley I/O links and it enables the terminals to communicate with PLC/SLC controllers, transfer applications, and communicate with I/O scanners. Among other things, the RS-232 port has printing support. All PanelView 1000 terminals are suitable for use in environments where the operating temperature does not fall outside a range of 0 to 55 degrees Celsius.
PanelView 1000 Startup Failure
If your PanelView 1000 fails to startup properly, always check the power supply first. Ensure the terminal is receiving the correct voltage and that the wiring and connections to the power source are valid. In addition, you should also ensure the DC power positive and negative are attached to the proper terminals.
PanelView 1000 Status Indicators
The status indicators are located on the back of your PanelView 1000 terminal. The COMM indicator is green and reflects communication. The FAULT indicator is red and reflects hardware faults. Upon startup, the fault indicator should be off and the comm indicator on. If the fault indicator flashes a few times at startup, this is not a concern. However, if both indicators are off you should check the power cable. See the table below to interpret the terminal's indicator status:
| Indicator | Status | Meaning |
| Comm | On | Normal Operation |
| Off |
Fault Present- Ensure controller is in run mode. Check baud settings of controller/terminal. Check for proper controller connections. |
|
| Blinking | Failed to establish communication | |
| Fault | On |
Fault Present - Restart terminal. If the error persists, the terminal requires servicing. Click here for information about DO Supply's repair service. |
| Off | Normal Operation | |
| Blinking | No applications loaded/application is corrupt. Reload the application. |
| Indicator | Status | Meaning |
| Comm | On | Normal operation |
| Off | Hardware failure | |
| Blinking | Failed to establish communication | |
| Fault | On | Hardware failure. |
| Off | Normal operation | |
| Blinking | Application not loaded/application is corrupt |
| Indicator | Status | Meaning |
| Comm | On | Normal operation |
| Off | Communication non-functional | |
| Blinking | Failed to establish communication, PLC may be in program mode | |
| Fault | On |
Fault Present - Check baud rate and rack settings. Ensure proper connections from terminal to controller. Verify remote I/O is enabled. |
| Off | Normal Operation | |
| Blinking | Application not loaded/application is corrupt |
PanelView 1000 Application Issues
| Issue | Possible Cause | Action |
| Failed Application Download (Initial Attempt) | Disconnected Communication Cable | Check cable type and connection |
| Improper Computer COM Port Selection | Ensure you have the correct COM port number in PanelBuilder32 or WinPFT software | |
| Communication Settings/Rate Incorrect | Ensure computer and terminal share the same communication settings | |
| Failed Application Download (Subsequent Attempts) | Communication Settings/Rate Incorrect | Ensure computer and terminal share the same communication settings. Adjust settings in the Communication Setup screen |
| Application File Name Appears as ******* | Invalid Application | Redownload application |
| Unusable Application Due to Error | Download new application | |
| Failed Application Transfer from Memory Card | Memory card incorrectly installed | Reinstall, verify its installed correctly |
| Application to Large for Terminal Memory | Reduce application size | |
| Incorrect Data Checksum | Ensure memory card is properly seated. It is possible the application may be corrupt | |
| File Format Invalid | Verify file format (.PVA) | |
| Failed Application Transfer to Memory Card | Memory card incorrectly installed | Reinstall, verify its installed correctly |
| Memory Card May be Wire Protected | Change memory card protection switch | |
| Another File on the Memory Card | Erase/reformat card | |
| Application to Large | Reduce application size, erase/reformat card | |
| Memory Card Format Invalid | Replace/reformat card | |
| Incorrect Data Checksum | Ensure card is installed correctly | |
| Application Does Not Exist | Ensure application exists |
Repair Your PanelView 1000
Here at DO Supply, we offer repair services for your Allen-Bradley products, such as the Allen-Bradley PanelView 1000. For more information or to request a quote, click here.