2711-T10G8L1X
This HMI terminal supports a resolution of 640 × 480 pixels and operates in a 4-tone grayscale mode. It is powered by a 24 V DC supply voltage that can range from 18 to 32 V. The 2711-T10G8L1X termina
In Stock Ships Today
5.0
Free UPS Ground on All Parcel Orders!
+1 (919) 205-4392
Allen Bradley Panelview 1000
The PanelView Standard 1000 Graphic Terminals have a 10 in. grayscale or color flat-panel display with a resolution of 640 x 480. For specific PanelView terminals, PanelView is replaced with the PV abbreviation. For example: PV1000 refers to the PanelView 1000 terminal. These terminals support operator input via keypad, via touch screen or via keypad with touch screen.
Learn more
Browse Panelview 1000
Browse available units in our catalog of Panelview 1000.
2711-K10G20L1X
In Stock Ships Today
4.5
2711-NC17X
This cable assembly is rated for voltages between 85 and 264 V AC or 24 V DC, with a length of 3.0 meters. It features 9-pin D-shell connectors on both ends. The assembly is suitable for use with spec
Available
4.5
2711-K10C10X
Available
5.0
2711-T10C10L1X
This HMI terminal integrates a full-color display and a viewing area measuring 211 × 158 mm. Equipped with DeviceNet and RS-232 communication ports, it supports external devices. Operating temperature
Available
5.0
2711-K10G15L1X
This device operates with an input voltage range of 18 to 32 VDC, typically using 24 VDC, and draws around 24 watts, equating to roughly 1 amp at 24 VDC. It includes approximately 310 KB of applicatio
In Stock Ships Today
5.0
2711-K10G16X
This PanelView 1000 unit offers an operational temperature range between 0 and 55 °C and a storage capability from -20 to 70 °C. It supports both AC and DC power inputs, drawing a maximum of ~55 VA. E
Available
5.0
2711-T10G15L1X
This model's touchscreen interface operates at a nominal voltage of 24 V DC and draws approximately 24 W of power. It includes memory capabilities of around 1 MB for application storage and approximat
In Stock Ships Tomorrow
5.0
2711-T10G9L1X
This HMI terminal features a display resolution of 640 x 480 pixels, providing clear visuals on a visible area measuring 211 x 158 mm. With a power input requirement of 24 V DC and a maximum power dra
In Stock Ships Today
5.0
2711-K10G20X
In Stock Ships Today
5.0
Showing 121-130 of
185
results
About Panelview 1000
The PanelView 1000 Series is a family of Allen-Bradley PanelView Standard Operator Terminals that provide a range of control and monitoring capabilities that are suitable for industrial applications. The display type on each terminal is an Active Matrix Thin-Film Transistor (TFT) with a cold cathode fluorescent backlight. They are available in 640 by 480 pixels, monochrome, grayscale (4 gray colors), and color (32 colors) displays with 8.3 x 6.2-inch dimensions. The touchscreen, keypad, or touchscreen and keypad combination input options are available for the terminals in this series and they have NEMA Type 12/13, IP 54, 4X (indoor use), and IP 65 enclosures to meet the environmental requirements of different applications.
The PanelView 1000 terminals are available in 85 to 264 Volts AC or 85 to 32 Volts DC power ratings. Both the PV1000G and the PV1000C models have a flash memory of 1008 KB. The touchscreen versions weigh 3 kilograms while the keypad models weigh 3.06 kilograms. The flat and lightweight design of these terminals saves mounting space and each unit has 6 mounting clips for convenience. Applications for the PanelView 1000 terminals can be created with the PanelBuilder32 software. Their communication options include 1 RS-232 port and 1 Remote I/O communication port. The Remote I/O port on PanelView 1000 operator terminals is compatible with all Allen-Bradley I/O links and it enables the terminals to communicate with PLC/SLC controllers, transfer applications, and communicate with I/O scanners. Among other things, the RS-232 port has printing support. All PanelView 1000 terminals are suitable for use in environments where the operating temperature does not fall outside a range of 0 to 55 degrees Celsius.
PanelView 1000 Startup Failure
If your PanelView 1000 fails to startup properly, always check the power supply first. Ensure the terminal is receiving the correct voltage and that the wiring and connections to the power source are valid. In addition, you should also ensure the DC power positive and negative are attached to the proper terminals.
PanelView 1000 Status Indicators
The status indicators are located on the back of your PanelView 1000 terminal. The COMM indicator is green and reflects communication. The FAULT indicator is red and reflects hardware faults. Upon startup, the fault indicator should be off and the comm indicator on. If the fault indicator flashes a few times at startup, this is not a concern. However, if both indicators are off you should check the power cable. See the table below to interpret the terminal's indicator status:
| Indicator | Status | Meaning |
| Comm | On | Normal Operation |
| Off |
Fault Present- Ensure controller is in run mode. Check baud settings of controller/terminal. Check for proper controller connections. |
|
| Blinking | Failed to establish communication | |
| Fault | On |
Fault Present - Restart terminal. If the error persists, the terminal requires servicing. Click here for information about DO Supply's repair service. |
| Off | Normal Operation | |
| Blinking | No applications loaded/application is corrupt. Reload the application. |
| Indicator | Status | Meaning |
| Comm | On | Normal operation |
| Off | Hardware failure | |
| Blinking | Failed to establish communication | |
| Fault | On | Hardware failure. |
| Off | Normal operation | |
| Blinking | Application not loaded/application is corrupt |
| Indicator | Status | Meaning |
| Comm | On | Normal operation |
| Off | Communication non-functional | |
| Blinking | Failed to establish communication, PLC may be in program mode | |
| Fault | On |
Fault Present - Check baud rate and rack settings. Ensure proper connections from terminal to controller. Verify remote I/O is enabled. |
| Off | Normal Operation | |
| Blinking | Application not loaded/application is corrupt |
PanelView 1000 Application Issues
| Issue | Possible Cause | Action |
| Failed Application Download (Initial Attempt) | Disconnected Communication Cable | Check cable type and connection |
| Improper Computer COM Port Selection | Ensure you have the correct COM port number in PanelBuilder32 or WinPFT software | |
| Communication Settings/Rate Incorrect | Ensure computer and terminal share the same communication settings | |
| Failed Application Download (Subsequent Attempts) | Communication Settings/Rate Incorrect | Ensure computer and terminal share the same communication settings. Adjust settings in the Communication Setup screen |
| Application File Name Appears as ******* | Invalid Application | Redownload application |
| Unusable Application Due to Error | Download new application | |
| Failed Application Transfer from Memory Card | Memory card incorrectly installed | Reinstall, verify its installed correctly |
| Application to Large for Terminal Memory | Reduce application size | |
| Incorrect Data Checksum | Ensure memory card is properly seated. It is possible the application may be corrupt | |
| File Format Invalid | Verify file format (.PVA) | |
| Failed Application Transfer to Memory Card | Memory card incorrectly installed | Reinstall, verify its installed correctly |
| Memory Card May be Wire Protected | Change memory card protection switch | |
| Another File on the Memory Card | Erase/reformat card | |
| Application to Large | Reduce application size, erase/reformat card | |
| Memory Card Format Invalid | Replace/reformat card | |
| Incorrect Data Checksum | Ensure card is installed correctly | |
| Application Does Not Exist | Ensure application exists |
Repair Your PanelView 1000
Here at DO Supply, we offer repair services for your Allen-Bradley products, such as the Allen-Bradley PanelView 1000. For more information or to request a quote, click here.