2711-NC17
This remote port assembly features a cable length of 3.1 meters (10 feet) and complies with the RS-232 communication standard. It connects via a 9-pin D-shell terminal and is compatible with devices s
Call
4.5
Free UPS Ground on All Orders!
+1 (919) 205-4392
Allen Bradley Panelview 1000
The PanelView Standard 1000 Graphic Terminals have a 10 in. grayscale or color flat-panel display with a resolution of 640 x 480. For specific PanelView terminals, PanelView is replaced with the PV abbreviation. For example: PV1000 refers to the PanelView 1000 terminal. These terminals support operator input via keypad, via touch screen or via keypad with touch screen.
Learn more
Browse Panelview 1000
Browse available units in our catalog of Panelview 1000.
2711-T10G8X
The 2711-T10G8X HMI features a 10-inch grayscale display and is optimized for panel mounting. The unit supports RS-232 and DH+ communication protocols and requires an input voltage range of 100–240 VA
In Stock Ships Tomorrow
4.6
2711-T10C9X
This model's power consumption is rated at 70 VA, and it supports communication through RS-232 (DH-485) and an RS-232 printer port. The touchscreen serves as the input method, with specified current r
In Stock Ships Today
4.7
2711-NR5K
The Allen Bradley Panelview 1000 series 2711-NR5K keypad terminal cutout accommodates 12-inch displays, making it suitable for applications with PanelView 1200 terminals. With an operational weight of
In Stock Ships Today
5.0
2711-T10C3X
This Allen Bradley HMI device has an enclosure rated at NEMA 4X and IP66, ensuring protection against water and dust. It includes a 24V DC power supply and features both Ethernet and USB ports for com
In Stock Ships Today
5.0
2711-T10C1X
This HMI operates with a power supply range of 85 to 264V AC and is designed for panel mounting. The unit features communication ports, including Remote I/O and an RS-232 printer ports. The enclosure
In Stock Ships Today
5.0
2711-K10G9X
The Panelview 1000 series includes the 2711-K10G9X interface terminal, which has a 10-inch display size. This device operates on an input voltage range of 85 to 264V AC at 47 to 63 Hz, with a maximum
In Stock Ships Tomorrow
4.9
2711-NV6T
The dimensions of the 2711-NV6T antiglare overlay are as follows: a height of 1.905 cm, a width of 38.71 cm, and a length of 45.999 cm. It operates effectively in humidity levels from 5% to 95% (non-c
Available
4.5
2711-K10G8L1X
This operator interface features a hardware keypad method, enabling efficient input operations. It operates on a supply voltage of 24 V DC, with an acceptable range between 18 to 32 V DC. The device a
Available
4.7
2711-K10G8X
This PanelView 1000 terminal model features a numeric keypad with 16 keys for user input. It is rated for use in environments classified under NEMA Type 12/13 or 4X, ensuring it can withstand harsh co
Available
4.8
Showing 81-90 of
184
results
About Panelview 1000
The PanelView 1000 Series is a family of Allen-Bradley PanelView Standard Operator Terminals that provide a range of control and monitoring capabilities that are suitable for industrial applications. The display type on each terminal is an Active Matrix Thin-Film Transistor (TFT) with a cold cathode fluorescent backlight. They are available in 640 by 480 pixels, monochrome, grayscale (4 gray colors), and color (32 colors) displays with 8.3 x 6.2-inch dimensions. The touchscreen, keypad, or touchscreen and keypad combination input options are available for the terminals in this series and they have NEMA Type 12/13, IP 54, 4X (indoor use), and IP 65 enclosures to meet the environmental requirements of different applications.
The PanelView 1000 terminals are available in 85 to 264 Volts AC or 85 to 32 Volts DC power ratings. Both the PV1000G and the PV1000C models have a flash memory of 1008 KB. The touchscreen versions weigh 3 kilograms while the keypad models weigh 3.06 kilograms. The flat and lightweight design of these terminals saves mounting space and each unit has 6 mounting clips for convenience. Applications for the PanelView 1000 terminals can be created with the PanelBuilder32 software. Their communication options include 1 RS-232 port and 1 Remote I/O communication port. The Remote I/O port on PanelView 1000 operator terminals is compatible with all Allen-Bradley I/O links and it enables the terminals to communicate with PLC/SLC controllers, transfer applications, and communicate with I/O scanners. Among other things, the RS-232 port has printing support. All PanelView 1000 terminals are suitable for use in environments where the operating temperature does not fall outside a range of 0 to 55 degrees Celsius.
PanelView 1000 Startup Failure
If your PanelView 1000 fails to startup properly, always check the power supply first. Ensure the terminal is receiving the correct voltage and that the wiring and connections to the power source are valid. In addition, you should also ensure the DC power positive and negative are attached to the proper terminals.
PanelView 1000 Status Indicators
The status indicators are located on the back of your PanelView 1000 terminal. The COMM indicator is green and reflects communication. The FAULT indicator is red and reflects hardware faults. Upon startup, the fault indicator should be off and the comm indicator on. If the fault indicator flashes a few times at startup, this is not a concern. However, if both indicators are off you should check the power cable. See the table below to interpret the terminal's indicator status:
| Indicator | Status | Meaning |
| Comm | On | Normal Operation |
| Off |
Fault Present- Ensure controller is in run mode. Check baud settings of controller/terminal. Check for proper controller connections. |
|
| Blinking | Failed to establish communication | |
| Fault | On |
Fault Present - Restart terminal. If the error persists, the terminal requires servicing. Click here for information about DO Supply's repair service. |
| Off | Normal Operation | |
| Blinking | No applications loaded/application is corrupt. Reload the application. |
| Indicator | Status | Meaning |
| Comm | On | Normal operation |
| Off | Hardware failure | |
| Blinking | Failed to establish communication | |
| Fault | On | Hardware failure. |
| Off | Normal operation | |
| Blinking | Application not loaded/application is corrupt |
| Indicator | Status | Meaning |
| Comm | On | Normal operation |
| Off | Communication non-functional | |
| Blinking | Failed to establish communication, PLC may be in program mode | |
| Fault | On |
Fault Present - Check baud rate and rack settings. Ensure proper connections from terminal to controller. Verify remote I/O is enabled. |
| Off | Normal Operation | |
| Blinking | Application not loaded/application is corrupt |
PanelView 1000 Application Issues
| Issue | Possible Cause | Action |
| Failed Application Download (Initial Attempt) | Disconnected Communication Cable | Check cable type and connection |
| Improper Computer COM Port Selection | Ensure you have the correct COM port number in PanelBuilder32 or WinPFT software | |
| Communication Settings/Rate Incorrect | Ensure computer and terminal share the same communication settings | |
| Failed Application Download (Subsequent Attempts) | Communication Settings/Rate Incorrect | Ensure computer and terminal share the same communication settings. Adjust settings in the Communication Setup screen |
| Application File Name Appears as ******* | Invalid Application | Redownload application |
| Unusable Application Due to Error | Download new application | |
| Failed Application Transfer from Memory Card | Memory card incorrectly installed | Reinstall, verify its installed correctly |
| Application to Large for Terminal Memory | Reduce application size | |
| Incorrect Data Checksum | Ensure memory card is properly seated. It is possible the application may be corrupt | |
| File Format Invalid | Verify file format (.PVA) | |
| Failed Application Transfer to Memory Card | Memory card incorrectly installed | Reinstall, verify its installed correctly |
| Memory Card May be Wire Protected | Change memory card protection switch | |
| Another File on the Memory Card | Erase/reformat card | |
| Application to Large | Reduce application size, erase/reformat card | |
| Memory Card Format Invalid | Replace/reformat card | |
| Incorrect Data Checksum | Ensure card is installed correctly | |
| Application Does Not Exist | Ensure application exists |
Repair Your PanelView 1000
Here at DO Supply, we offer repair services for your Allen-Bradley products, such as the Allen-Bradley PanelView 1000. For more information or to request a quote, click here.