- Bad communication ports
- Broken selector/key switches
- Dead batteries/Bad Battery connections
- Solid or Blinking RED OK Status Light
- Solid or Blinking RED RUN Status Light
- Solid or Blinking RED Fault Status Light
Free UPS Ground on All Orders!
+1 (919) 205-4392
Allen Bradley Micro 810 Repair
We offer extensive repairs for your Micro 810. We keep many spare parts in stock so that we can repair your Micro 810 as efficiently and effectively as possible. Our standard repair lead time is 2-4 weeks. However, we can often repair your unit much faster if necessary. We can repair most issues with your Micro 810 and if for some reason we cannot repair your unit we will do our best to offer a refurbished unit at the repair cost, so that you can get a working unit back as soon as possible!
- 2 Year DO Supply Warranty
- Fast repairs at low costs
- No surprises or up-charges for difficult repairs
- Standard lead time of 2-4 weeks
- Extensive quality control and testing
Get a repair quote
Not an Authorized Distributor: DO Supply is not an authorized distributor for listed manufacturers or tradenames and therefore the manufacturer's
warranty does not apply. All of our products come with DO Supply's 2-year warranty.
Learn more
Hardware issues & error codes we repair
We repair all of the following hardware issues and error codes with your Micro 810 parts.
- Bad analog inputs or ouptus
- Bad digital input or outputs
- Bad relays (stuck on/off)
- Incorrect voltages on inputs or outputs
- Incorrect current on inputs or outputs
- DF1, DH-485, DH+, Profibus, Remote I/ (RIO) failures and more!
- Intermittent communication
- Solid RED/Blinkging RED communication lights
- Devicenet, Ethernet, ControlNet, RS232 ports.
- Missing CJC Jumpers
- Incorrect readings
- Failed inputs
- Dead power supplies
- Incorrect voltage
- Broken Plastic
- Poor Connections
- Bad Slots
Browse Micro 810 Repairs
Browse our catalog of repairable Micro 810 parts to get a quote.
2080-LC10-12AWA
This Micro 810 Programmable Logic Controller is a 4-Relay Output Controller with a 8-120/240V AC Input.
In Stock Ships Tomorrow
2080-LC10-12DWD
This Micro 810 Programmable Logic Controller is a 4-Relay Output Controller with a 8-12V DC Input.
Call
2080-LC10-12QBB
This Micro 810 Programmable Logic Controller is a 4-24V DC Source Output Controller with a 8-24V DC/V AC Input.
In Stock Ships Today
2080-LC10-12QWB
The Micro 810 series controller includes four digital inputs and four versatile inputs that can be configured for either analog or digital signals. It operates on a voltage range between 20.4 and 26.4
Available
2080-USBADAPTER
This USB adapter supports Micro810 12-point devices and operates in non-hazardous environments. For hazardous settings, it meets Class 1 Division 2 standards for Groups A, B, C, and D. The product fea
Call
810-A12C
This Inverse Time Relay operates at a voltage of 600 volts and supports a maximum current of 56 amperes. It is specifically designed to use copper wire connections only. Both the minimum operating cur
In Stock Ships Today
Showing 1-6 of
6
results
About Micro 810
The Micro 810 series is a logic controller system series with products that are all small. These logic controllers act as smart relays with high current relay outputs. They have the programming capabilities of micro PLCs. The controllers come with 8 Amps of input. It has a 20-form factor and uses 6 catalogs for selection and user preference. The Micro 810 series controllers are mostly used with smaller machines and remote automation devices. The controllers come with microSD card slots that are used to store project data and restore it when needed. The networking and communication are done through an embedded 10/100 Base-T Ethernet port which is an RJ-45 port. It also features the embedded non-isolated RS-232 and the RS-485 combo serial port. The logic controller supports the Modbus RTU protocol, Modus TCP, Ethernet/IP, and the CIP series protocol. The controller uses USB 2.0 ports as communication ports. The logic controller is not compatible with plugin modules.
The front side of the Micro 810 controllers house LED indicators which shows the running status, communication status, and fault status updates. The top and bottom parts are clamped with terminals on the front. The logic controllers have power consumption ratings of 3 Watts. The analog input voltage range of the 810 controllers lies between 0 and 10 Volts DC. The Micro 810 controllers operate with a frequency of 50/60 Hertz. The off-state maximum current of the logic controllers is 0.095 milliAmps. The controllers dissipate a maximum power of 6 Watts. The temperature should be between -20 and 65 degrees Celsius for normal operation. The environment should be relatively humid with 5 to 95% non-condensing humidity. The controller is certified with the CE, RCM, KC, and other standards.