- Bad communication ports
- Broken selector/key switches
- Dead batteries/Bad Battery connections
- Solid or Blinking RED OK Status Light
- Solid or Blinking RED RUN Status Light
- Solid or Blinking RED Fault Status Light
Free UPS Ground on All Orders!
+1 (919) 205-4392
Allen Bradley Point I/O 1734 Repair
We offer extensive repairs for your Point I/O 1734. We keep many spare parts in stock so that we can repair your Point I/O 1734 as efficiently and effectively as possible. Our standard repair lead time is 2-4 weeks. However, we can often repair your unit much faster if necessary. We can repair most issues with your Point I/O 1734 and if for some reason we cannot repair your unit we will do our best to offer a refurbished unit at the repair cost, so that you can get a working unit back as soon as possible!
- 2 Year DO Supply Warranty
- Fast repairs at low costs
- No surprises or up-charges for difficult repairs
- Standard lead time of 2-4 weeks
- Extensive quality control and testing
Get a repair quote
Not an Authorized Distributor: DO Supply is not an authorized distributor for listed manufacturers or tradenames and therefore the manufacturer's
warranty does not apply. All of our products come with DO Supply's 2-year warranty.
Learn more
Hardware issues & error codes we repair
We repair all of the following hardware issues and error codes with your Point I/O 1734 parts.
- Bad analog inputs or ouptus
- Bad digital input or outputs
- Bad relays (stuck on/off)
- Incorrect voltages on inputs or outputs
- Incorrect current on inputs or outputs
- DF1, DH-485, DH+, Profibus, Remote I/ (RIO) failures and more!
- Intermittent communication
- Solid RED/Blinkging RED communication lights
- Devicenet, Ethernet, ControlNet, RS232 ports.
- Missing CJC Jumpers
- Incorrect readings
- Failed inputs
- Dead power supplies
- Incorrect voltage
- Broken Plastic
- Poor Connections
- Bad Slots
Browse Point I/O 1734 Repairs
Browse our catalog of repairable Point I/O 1734 parts to get a quote.
1734-AENTRK
This module is designed to facilitate communication over an Ethernet/IP network, supporting maximum expansion capacity of 63 modules. The adapter is equipped with two Ethernet ports, allowing multiple
In Stock Ships Today
1734-APB
The Allen-Bradley 1734-APB is a POINT I/O PROFIBUS DP Network Adapter. It has 24 Volts DC Input Voltage and a Field Side Power of 400 milliamps with an Inrush Current of 6 amps. This PROFIBUS DP Netwo
In Stock Ships Today
1734-ARM
This address reserve module operates with a current consumption of 75 mA from the POINTbus and has a power dissipation rating of 0.375 watts. Suitable for DIN rail installation, it features an open-st
In Stock Ships Today
1734-CTM
This common terminal module features a single-slot installation type and operates with a passive electrical interface. Compatible with 3-wire field devices, it supports various terminal bases such as
In Stock Ships Today
1734-EP24DC
Designed to operate at a nominal voltage of 24 volts DC, this unit has an input voltage range from 10 to 28.8 volts DC. Indicators include a green field power status light and a green 5-volt system po
In Stock Ships Today
1734-EP24DCK
This expansion power supply features an input current of 400 mA and can provide up to 1.3 Amps of output current. It is designed for DIN-rail mounting and has an open-style enclosure. The unit comes w
In Stock Ships Today
1734-EPAC
The Allen-Bradley 1734-EPAC is a POINT I/O Expansion Power Supply. It has 120 or 240 Volts AC Field Power and an Inrush Current of 2 amps for 6 milliseconds with MOV and Fuse Overvoltage Protection. T
In Stock Ships Today
1734-EXT1
This bus extension cable features a total of 10 positions and utilizes screw terminals for secure electrical connections. Operating temperatures range from -20°C to +55°C, while it can be stored at te
Call
1734-EXT3
This cable supports 1734 Point I/O modules and operates effectively at a voltage range of 10 to 28.8 volts DC. It withstands vibrations of 5G across a frequency range of 10 to 500 Hertz and is built t
Call
1734-FPD
Designed to fit within the POINT I/O system, the 1734-FPD operates with a nominal input of 120/240V AC and 12/24V DC, with a DC input voltage range of 10 to 28.8V DC. This module is open-style and sup
In Stock Ships Today
Showing 11-20 of
121
results
About Point I/O 1734
The Allen-Bradley 1734 Point I/O modules are available as digital, analog, specialty, AC/DC, RTD, Thermocouple, and point guard safety-rated input/output modules for a range of applications. Each module has 1 to 8-point channel density and they support producer/consumer technology for sharing input information and output status between multiple Logix controllers. Four of the main components of the Point I/O 1734 modules are communication interface modules, terminal base units, power distribution modules, and field interface and system-interface circuitry. The network protocols available for modules in the Point I/O 1734 product family include the EtherNet/IP, ControlNet, DeviceNet, Profibus, and other open network protocols. They allow up to 504 channels on a single network interface. The modular design and removable terminations offer the flexibility and cost-effectiveness of using only the modules that the users’ specific applications require. They also allow for the side-by-side operation of standard I/O and safe I/O in the same chassis, and they support local and remote operation.
Point I/O 1734 modules are a major component of Allen-Bradley Automation Integrated Architecture systems and they offer channel-level diagnostics for fast and seamless troubleshooting. Modules in this family are equipped with user-configurable features, including channel-level alarm announcements and channel-level short-circuit detection with electronic feedback to meet application-specific requirements. Point I/O 1734 modules have remove and insert under power (RIUP) support to allow for maintenance while the system is running and the modules and base units can be mounted horizontally or vertically without impeding performance. The full add-on profiles for programming Point I/O 1734 modules are available in the Studio 5000 and RSLogix 5000 computer software.