- Bad communication ports
- Broken selector/key switches
- Dead batteries/Bad Battery connections
- Solid or Blinking RED OK Status Light
- Solid or Blinking RED RUN Status Light
- Solid or Blinking RED Fault Status Light
Free UPS Ground on All Orders!
+1 (919) 205-4392
Allen Bradley PLC 5 Repair
We offer extensive repairs for your PLC 5. We keep many spare parts in stock so that we can repair your PLC 5 as efficiently and effectively as possible. Our standard repair lead time is 2-4 weeks. However, we can often repair your unit much faster if necessary. We can repair most issues with your PLC 5 and if for some reason we cannot repair your unit we will do our best to offer a refurbished unit at the repair cost, so that you can get a working unit back as soon as possible!
- 2 Year DO Supply Warranty
- Fast repairs at low costs
- No surprises or up-charges for difficult repairs
- Standard lead time of 2-4 weeks
- Extensive quality control and testing
Get a repair quote
Not an Authorized Distributor: DO Supply is not an authorized distributor for listed manufacturers or tradenames and therefore the manufacturer's
warranty does not apply. All of our products come with DO Supply's 2-year warranty.
Learn more
Hardware issues & error codes we repair
We repair all of the following hardware issues and error codes with your PLC 5 parts.
- Bad analog inputs or ouptus
- Bad digital input or outputs
- Bad relays (stuck on/off)
- Incorrect voltages on inputs or outputs
- Incorrect current on inputs or outputs
- DF1, DH-485, DH+, Profibus, Remote I/ (RIO) failures and more!
- Intermittent communication
- Solid RED/Blinkging RED communication lights
- Devicenet, Ethernet, ControlNet, RS232 ports.
- Missing CJC Jumpers
- Incorrect readings
- Failed inputs
- Dead power supplies
- Incorrect voltage
- Broken Plastic
- Poor Connections
- Bad Slots
Browse PLC 5 Repairs
Browse our catalog of repairable PLC 5 parts to get a quote.
1784-F30D
The Allen Bradley 1784-F30D serves as a remote I/O expansion module compatible with plant floor terminals. This slave module links to an I/O scanner and supports operational baud rates of up to 230.4
In Stock Ships Today
1784-KL
The 1784-KL module connects via a D-sub connector with a pin count of 37, providing robust communication capabilities. This device operates efficiently within a temperature range of 0°C to 60°C and to
In Stock Ships Today
1784-KR
This interface module incorporates DH-485 as the network protocol and features an ISA bus interface. It connects via a 15-pin D-shell connector, adhering to the RS-485 standard. The 1784-KR operates e
In Stock Ships Today
1784-KT
The Allen-Bradley 1784-KT module is a module which is installed in personal computers and allows for interfacing with DH+ networks. The 1784-KT module is an ISA card which can be installed in 8-bit an
In Stock Ships Today
1784-KT2
Communication Interface Module, PLC-2 Serial Interface, PLC-3 Serial Interface, and Data Highway Plus Outputs, 62-Pin D-Shell Module Output Connector
In Stock Ships Today
1784-KTC
Designed specifically for ControlNet applications, the 1784-KTC interface card provides a data rate of 5 Mbps. It efficiently updates the network within a time range of 2 to 100 ms. The module accommo
In Stock Ships Today
1784-KTCS
This ControlNET scanner card allows a maximum of four cards to be installed per computer. Its operational temperature ranges from 0°C to 50°C, with a storage temperature capacity between -40°C and 85°
In Stock Ships Today
1784-KTCX
ControlNet Interface Card, Dual-Port BNC, 1.25 Only ControlNet Phase
In Stock Ships Today
1784-KTCX15
This interface card has a memory requirement of 16 KB dual-port RAM and operates at a data transfer rate of 5 Mbps, aligning with ControlNet protocols (CIP). The device supports dual-channel redundanc
In Stock Ships Today
1784-KTS
This communication interface card is compatible with 16-bit ISA and EISA slots. Its operational temperature range varies from 0°C to 60°C, while storage temperatures can reach as low as -40°C and as h
In Stock Ships Today
Showing 391-400 of
532
results
About PLC 5
The PLC 5 controllers series is a series of programmable controllers which are used at the center of a machine architecture system which brings together existing and future networks by using different types of networks, including Ethernet/IP, ControlNet, and DeviceNet networks. They offer connectivity between the SLC 500, ControlLogix, and MicroLogix controllers. These controllers can help to control the architecture and offer cost-effective connections to a wide range of devices. They feature input/output modules inside a single chassis with a power supply. The PLC 5 controllers come with onboard remote I/O scanner ports and onboard extended I/O scanner ports. These controllers are available in a wide range of input/output capacities and memory sizes. They can also be connected to a wide variety of networks for distributed processing and distributed input/output.
The PLC 5 controllers come with several programming features that help to serve different application demands. They come with ladder logic which programs a language and is representative of the relay logic. The subroutines in the controllers help to store the recurring sections of the program logic which can be accessed from multiple program files. They also feature sequential functional charts and structured texts. The PLC 5 controllers come with a maximum of 16 module I/O slots. Also, the controllers can be mounted by using a back panel or by using a rack. A wide variety of data formats are available in the PLC series. No external power is required for the controllers. The PLC 5 controllers are also available based on the number of user memory words, memory size, processor types. The PLC 5 controllers are also available with different input resolutions, input types, and output resolutions. Various operating voltages can be used to run the controllers. Multiple LED indicators are housed in the PLC 5 controllers to show different information.
Common error/issues withe PLC 5 include:
Plastics, power supply, enclosure and mounting
Mounting clips
Dismounting clips
Racking guides
Grounding clip
Dead backplane
Stripped threads
Damaged rack
no power through AUX power
Damaged power board
Power pins
Node address switches
Communications
RS-232
DH+ ports
Ethernet port
Side mounted port
No connection
Loss of communications
No communications
Faulty key switch
Lights
BATT light
Solid PROG lights
LED indicators
I/O
Discrete output replacement relay or TRIAC
Discrete input replacement
Analog out
Analog in
RTD channel repair
Fused input/output replacement